1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 5 of 5
  1. 4sfaloth
    Post

    Solved R1+ failing auto-leveling

    I see. Not sure if I can see/access the RAMPS board, but the wires going into the switches seem fine at visual inspection. Is there any way to...
    Post by: 4sfaloth, Dec 8, 2018 in forum: Troubleshooting
  2. 4sfaloth
    Post

    Solved R1+ failing auto-leveling

    it's just the camera angle, it is straight
    Post by: 4sfaloth, Dec 8, 2018 in forum: Troubleshooting
  3. 4sfaloth
    Post

    Solved R1+ failing auto-leveling

    just managed to upload the calibration video to youtube: [MEDIA] The video start on the 2nd step of calibration
    Post by: 4sfaloth, Dec 8, 2018 in forum: Troubleshooting
  4. 4sfaloth
    Post

    Solved R1+ failing auto-leveling

    Thanks. The symptons seem a lot like what is shown at 2m18s on that video, except that the carriage goes down on some of the steps, but not on...
    Post by: 4sfaloth, Dec 8, 2018 in forum: Troubleshooting
  5. 4sfaloth
    Post

    Solved R1+ failing auto-leveling

    Upload does not seem to be working unfortunately :S
    Post by: 4sfaloth, Dec 8, 2018 in forum: Troubleshooting
  6. 4sfaloth
    Thread

    Solved R1+ failing auto-leveling

    Hi all, My R1+ was printing fine yesterday, but today suddenly it seems like it fails every auto-leveling calibration and then begins printing in...
    Thread by: 4sfaloth, Dec 8, 2018, 19 replies, in forum: Troubleshooting
  7. 4sfaloth
    Post

    Answered Chunk of glass bed came off

    @Geof @WheresWaldo thank you all for your help. So many ideas to circumvent this :) Just one thing I don't really get; why does the printer come...
    Post by: 4sfaloth, Nov 13, 2018 in forum: Troubleshooting
  8. 4sfaloth
    Post

    Answered Chunk of glass bed came off

    So, just to make sure I understand you correctly, what you are suggesting is for me to go to a local shop and order a custom-sized piece of float...
    Post by: 4sfaloth, Nov 11, 2018 in forum: Troubleshooting
  9. 4sfaloth
    Post

    Answered Chunk of glass bed came off

    @WheresWaldo thank you for your reply. Not sure I am happy to know I did nothing wrong; I was hoping there would be something I could fix to...
    Post by: 4sfaloth, Nov 11, 2018 in forum: Troubleshooting
  10. 4sfaloth
    Thread

    Answered Chunk of glass bed came off

    Hi all, Basically during one of my prints (a small miniature) a fraction of the glass bed seems to have broken and glued itself to the part. The...
    Thread by: 4sfaloth, Nov 11, 2018, 16 replies, in forum: Troubleshooting
  11. 4sfaloth
    Post

    Answered R1+ Prints Stuck in Bed

    Thank you both for your answer! I did not realize the hairspray also helped with the release in the end of the print. I'll try turning off the...
    Post by: 4sfaloth, Sep 9, 2018 in forum: Troubleshooting
  12. 4sfaloth
    Thread

    Answered R1+ Prints Stuck in Bed

    Hi all, I've got a R1+ printer since last July and overall am pretty satisfied with the results. I didn't change the stock parameters (the one...
    Thread by: 4sfaloth, Sep 9, 2018, 3 replies, in forum: Troubleshooting
Find older messages
Showing results 81 to 92 of 92
Search Again
Page 5 of 5