1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 7 of 10
  1. Mike Kelly
    Post

    Unanswered Ninjaflex

    If you remove the hot end does it feed through? I have some trouble getting ninjaflex into my filament tube. I have to take off the two tensioning...
    Post by: Mike Kelly, Feb 24, 2016 in forum: General Questions
  2. Mike Kelly
    Post

    Unresolved Noob with some of questions...

    I don't think Robo's stuff is that terrible, but it's also not the best. Somewhere below hatchbox but not the bottom of the barrel. I would use...
    Post by: Mike Kelly, Feb 24, 2016 in forum: Troubleshooting
  3. Mike Kelly
    Post

    Solved Bad day - clogged Hexagon hot end

    You also may be able to remove the brass inert at the top of the hot end (the brass thing around the filament in your picture) You should be able...
    Post by: Mike Kelly, Feb 24, 2016 in forum: Troubleshooting
  4. Mike Kelly
    Post

    Gcodeprintr for Android

    Is this what you were using @daniel871 ?
    Post by: Mike Kelly, Feb 24, 2016 in forum: General Questions
  5. Mike Kelly
    Post

    Unresolved Noob with some of questions...

    Stringing is a function of filament, retraction, and temperature settings. 210 is generally ok, but the Deprime Test object is a nice quick print...
    Post by: Mike Kelly, Feb 24, 2016 in forum: Troubleshooting
  6. Mike Kelly
    Post

    Problems with Robo 3D R1

    They've had little slots for the Z rods for a while now. If you don't have couplers on the Z axis lead screws you have an R1 +plus and MC should...
    Post by: Mike Kelly, Feb 24, 2016 in forum: Troubleshooting
  7. Mike Kelly
    Post

    question

    This is the free version.
    Post by: Mike Kelly, Feb 24, 2016 in forum: General Questions
  8. Mike Kelly
    Post

    Machinable Wax filament

    Sounds cool, though I think PLA is also good for lost investment casting as it burns out clean
    Post by: Mike Kelly, Feb 24, 2016 in forum: Printing Filament
  9. Mike Kelly
    Post

    Problems with Robo 3D R1

    What firmware/printer name is matter control saying? Is the fan on the bottom of your printer running? Does the printer home properly?
    Post by: Mike Kelly, Feb 24, 2016 in forum: Troubleshooting
  10. Mike Kelly
    Post

    Unresolved My printer won't turn on

    Loose connection? Look underneath and see if the green LED is on. Check the fuse as well if the green LED is not on. If you're not comfortable...
    Post by: Mike Kelly, Feb 24, 2016 in forum: Troubleshooting
  11. Mike Kelly
    Post

    Solved My printer seems dead! Need help ASAP!!

    Measure the voltage coming off the power supply. Measure the voltage going into the ramps. I'd suggest calling/emailing robo for support as well.
    Post by: Mike Kelly, Feb 24, 2016 in forum: Troubleshooting
  12. Mike Kelly
    Post

    Unanswered LED Lights Wires

    You know what they say when you assume. Look at where the wires are plugged in and note the orientation. Otherwise buy a multimeter. They're...
    Post by: Mike Kelly, Feb 24, 2016 in forum: Troubleshooting
  13. Mike Kelly
    Post

    NinjaFlex filament

    Those links don't work. Use the Upload a file feature until you have 3 posts then use imgur
    Post by: Mike Kelly, Feb 24, 2016 in forum: Printing Filament
  14. Mike Kelly
    Post

    New Stabilizer

    The smooth rod is the only thing that needs to be stabalized and you can just print some basic caps to secure them in the upper slots:...
    Post by: Mike Kelly, Feb 24, 2016 in forum: Mods and Upgrades
  15. Mike Kelly
    Post

    Solved Added lcd now this

    Use the lead screw upgrade firmware, AKA Robo3DR1PlusV1 v3 is for older non-Plus printers
    Post by: Mike Kelly, Feb 24, 2016 in forum: Troubleshooting
  16. Mike Kelly
    Post

    Answered How can I tell what version of FW I have?

    Then you have the latest version of Robo's firmware
    Post by: Mike Kelly, Feb 23, 2016 in forum: General Questions
  17. Mike Kelly
    Post

    Solved Cura and Surface Pro 3

    I guess I've never heard of anyone doing it but if it has USB input and can install arduino drivers I don't see why not
    Post by: Mike Kelly, Feb 23, 2016 in forum: General Questions
  18. Mike Kelly
    Post

    Unresolved Dual fan mod problems!

    Alternatively just reduce the fan speed
    Post by: Mike Kelly, Feb 23, 2016 in forum: Troubleshooting
  19. Mike Kelly
    Post

    Unresolved Print Quality issues

    I bet your ramps cooling fan is unplugged causing the Z axis to overheat. Verify that's plugged in and running when the printer is powered on
    Post by: Mike Kelly, Feb 23, 2016 in forum: Troubleshooting
  20. Mike Kelly
    Post

    Fans; Single or dual, shroud or no shroud

    Lately i've heard that one fan pointed generally at the print cooling the area and another fan ducted to cool the filament as it leaves the nozzle...
    Post by: Mike Kelly, Feb 23, 2016 in forum: Mods and Upgrades
Showing results 121 to 140 of 199 Next >
Search Again
Page 7 of 10