1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 10 of 10
  1. WheresWaldo
    Post

    Filament not loading. Clicking noise.

    Or possibly the nozzle is just too close to the bed. Usually the clicking is a result of too much backpressure and no flow, so look at that @mark...
    Post by: WheresWaldo, May 26, 2019 in forum: Troubleshooting
  2. WheresWaldo
    Post

    Robo3D may be out of the consumer market

    There probably needs to be an effort made to preserve some of the information here. I don't know how that would be done, I don't know the...
    Post by: WheresWaldo, May 24, 2019 in forum: Off Topic
  3. WheresWaldo
    Post

    Solved Jamming of Pla

    Also don't expect accuracy to the nearest degree, we are working with commodity Chinese electronics and a lookup table that is only a theoretical...
    Post by: WheresWaldo, May 23, 2019 in forum: Troubleshooting
  4. WheresWaldo
    Post

    Robo SD card 1.8.1-r2.1

    https://1drv.ms/u/s!AuAkU2AiD24nq1lH1odhIbl1H8Wx
    Post by: WheresWaldo, May 23, 2019 in forum: Mods and Upgrades
  5. WheresWaldo
    Thread

    Robo3D may be out of the consumer market

    Based on a few responses on their Facebook page, it appears all the Robo3D consumer printers are discontinued and no new models are expected...
    Thread by: WheresWaldo, May 23, 2019, 28 replies, in forum: Off Topic
  6. WheresWaldo
    Thread

    Robo SD card 1.8.1-r2.1

    Zip file, open with WinRAR or 7zip, use Etcher to burn onto a new SD card 8GB or larger. <link coming>
    Thread by: WheresWaldo, May 23, 2019, 1 replies, in forum: Mods and Upgrades
  7. WheresWaldo
    Post

    Answered Printing wood pla

    The first thing, use a bigger nozzle, the little wood powder in it will clog small nozzles. I typically use a 0.6 mm or larger. Also play with the...
    Post by: WheresWaldo, May 22, 2019 in forum: Troubleshooting
  8. WheresWaldo
    Post

    Power supply

    If you want a Meanwell this is the exact model you need, works on both the C2 and R2 GST220A24-R7B At Amazon...
    Post by: WheresWaldo, May 22, 2019 in forum: General Questions
  9. WheresWaldo
    Post

    Solved Jamming of Pla

    One note about PLA, it gets stickier the hotter you extrude it. Simply chemistry. But it does flow easier.
    Post by: WheresWaldo, May 20, 2019 in forum: Troubleshooting
  10. WheresWaldo
    Post

    Solved Jamming of Pla

    Usually you can take the recommendation and increase it by 10% with no issues, so if the filament maker says 190°C then you can usually go all the...
    Post by: WheresWaldo, May 20, 2019 in forum: Troubleshooting
  11. WheresWaldo
    Post

    Nylon Jamming in R2

    Slower and hotter might also be the ticket for Nylon on the R2. Personally I have never printed nylon on the R2 / C2. The other thing to do is try...
    Post by: WheresWaldo, May 20, 2019 in forum: Troubleshooting
  12. WheresWaldo
    Post

    Unresolved Printing With Supports Help Request

    Look here, https://www.matterhackers.com/mattercontrol/support/slice-settings/support/advanced, Apparently they call it Air Gap.
    Post by: WheresWaldo, May 18, 2019 in forum: Troubleshooting
  13. WheresWaldo
    Post

    Unresolved Printing With Supports Help Request

    I don't use MatterControl, but it should have something called an Interface Layer or Height, and that is the space between the top of the support...
    Post by: WheresWaldo, May 18, 2019 in forum: Troubleshooting
  14. WheresWaldo
    Post

    Unresolved Bed not heating - R23 light not turning on

    Another option is a RAMPS Arduino combo board, something like this...
    Post by: WheresWaldo, May 15, 2019 in forum: Troubleshooting
  15. WheresWaldo
    Post

    Solved Printhead fell apart?

    There is a hole in the side of the hot zone (the bottom part) of the printhead, stick the small glass bead in there and route the wires upward,...
    Post by: WheresWaldo, May 15, 2019 in forum: Troubleshooting
Find older messages
Showing results 181 to 195 of 195
Search Again
Page 10 of 10