1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 2 of 9
  1. Lance Weston
    Post

    BLTouch installation

    [ATTACH]
    Post by: Lance Weston, Aug 26, 2021 in forum: Mods and Upgrades
  2. Lance Weston
    Post

    BLTouch installation

    I do not know how you got to the servo0. Here are the pins on the headers. [ATTACH]
    Post by: Lance Weston, Aug 26, 2021 in forum: Mods and Upgrades
  3. Lance Weston
    Post

    BLTouch installation

    Post by: Lance Weston, Aug 26, 2021 in forum: Mods and Upgrades
  4. Lance Weston
    Thread

    Question about PETG

    I am printing with petg that has a temp range of 230C to 250C. I am printing at 240C. The parts printed solid plastic are large mechanical...
    Thread by: Lance Weston, Aug 25, 2021, 5 replies, in forum: Filament
  5. Lance Weston
    Post

    BLTouch installation

    The existing IR board has 3 connections: +5v, GND, signal. The signal returns to GND when the sensor is close to the plate. The pin numbers are...
    Post by: Lance Weston, Aug 25, 2021 in forum: Mods and Upgrades
  6. Lance Weston
    Post

    Trying to resurrect my R2

    Post by: Lance Weston, Aug 25, 2021 in forum: Mods and Upgrades
  7. Lance Weston
    Post

    Trying to resurrect my R2

    Post by: Lance Weston, Aug 24, 2021 in forum: Mods and Upgrades
  8. Lance Weston
    Post

    Trying to resurrect my R2

    That is exactly what my block implements. The only difference is I am using open loop belting. You need my block to be able to hit the x,y limit...
    Post by: Lance Weston, Aug 23, 2021 in forum: Mods and Upgrades
  9. Lance Weston
    Post

    Trying to resurrect my R2

    I can not visualize your description. can you provide a sketch?
    Post by: Lance Weston, Aug 23, 2021 in forum: Mods and Upgrades
  10. Lance Weston
    Post

    Trying to resurrect my R2

    This is a quick mock up of what the rear bearing block would look like without it's cap. I left the 6mm rod holes in for a better illustration....
    Post by: Lance Weston, Aug 19, 2021 in forum: Mods and Upgrades
  11. Lance Weston
    Post

    Trying to resurrect my R2

    This can all be made to work with the R2. I use a dual gear extruder. The 8mm rods passing through the print head sit on the outside of the GT2...
    Post by: Lance Weston, Aug 19, 2021 in forum: Mods and Upgrades
  12. Lance Weston
    Post

    Trying to resurrect my R2

    The bearings should work that way, but they will be short. Ideally you want a print head with no play or it will vibrates as it is drawn over the...
    Post by: Lance Weston, Aug 19, 2021 in forum: Mods and Upgrades
  13. Lance Weston
    Post

    Trying to resurrect my R2

    Yup, you are right. just did calculations and it is a little more than 50%. The distance between vertical centers of the 6 mm rods is 16.8 mm....
    Post by: Lance Weston, Aug 18, 2021 in forum: Mods and Upgrades
  14. Lance Weston
    Post

    Error Detected Connection Interrupted. Min Temp

    The problem is probably that your fans are too high. Try running at 10% and seeing if the problem goes away. There is no shield between the...
    Post by: Lance Weston, Aug 15, 2021 in forum: Troubleshooting
  15. Lance Weston
    Post

    Latest carriage rebuild parts

    Post by: Lance Weston, Aug 5, 2021 in forum: Mods and Upgrades
  16. Lance Weston
    Post

    Trying to resurrect my R2

    You must keep the existing 8mm rods in their current location, which precludes that thingiverse design. In my initial improvements I used...
    Post by: Lance Weston, Aug 5, 2021 in forum: Mods and Upgrades
  17. Lance Weston
    Post

    Trying to resurrect my R2

    The belt wraps around the 20 tooth gear determining how much plastic there is in the bearing block.. Increasing from a 6mm shaft to an 8mm shaft...
    Post by: Lance Weston, Aug 5, 2021 in forum: Mods and Upgrades
  18. Lance Weston
    Post

    Trying to resurrect my R2

    The problem with going to an 8mm shaft instead of 2 6mm is that the head must have no play If you use a quality slide bearing you can not make it...
    Post by: Lance Weston, Aug 5, 2021 in forum: Mods and Upgrades
  19. Lance Weston
    Post

    Trying to resurrect my R2

    The biggest factor in quality may not be the electronics. I just rebuilt an R2 carriage and the quality of print went way up. The bed moved...
    Post by: Lance Weston, Aug 1, 2021 in forum: Mods and Upgrades
  20. Lance Weston
    Post

    Trying to resurrect my R2

    All of the stuff I put on thingiverse for the Robo can not be found. They removed all of the Robo tags. Can you put it on google drive and post...
    Post by: Lance Weston, Jul 31, 2021 in forum: Mods and Upgrades
Showing results 21 to 40 of 167 Next >
Search Again
Page 2 of 9