1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 1 of 2
  1. Cuda70
    Post

    Unresolved Question about the NEW STYLE ramps board

    Thanks for all the help will try that :)
    Post by: Cuda70, Apr 22, 2016 in forum: Troubleshooting
  2. Cuda70
    Post

    Unresolved Question about the NEW STYLE ramps board

    Great info on the endstop wires the plug that goes from the extruder stepper motor to the ramps board and has a black plug that has several wires...
    Post by: Cuda70, Apr 22, 2016 in forum: Troubleshooting
  3. Cuda70
    Post

    Unresolved Question about the NEW STYLE ramps board

    A thousand thank yous for the photos i do not see the X_Y_Z end stop switch wires connected to the board ( is the black wire on the "-" pin ) and...
    Post by: Cuda70, Apr 22, 2016 in forum: Troubleshooting
  4. Cuda70
    Post

    Unresolved Question about the NEW STYLE ramps board

    sorry Geof but i cant find the photo
    Post by: Cuda70, Apr 22, 2016 in forum: Troubleshooting
  5. Cuda70
    Thread

    Unresolved Question about the NEW STYLE ramps board

    The "X"--"Y"--and "Z" connector going from the switches to the ramps board is the black wire placed on the - pin or the other pin and on the...
    Thread by: Cuda70, Apr 20, 2016, 11 replies, in forum: Troubleshooting
  6. Cuda70
    Post

    Printer Number 2

    I have a Wanhao Duplicator I3V2 Good printer with good print quality
    Post by: Cuda70, Apr 20, 2016 in forum: Projects
  7. Cuda70
    Post

    Solved Something crazy just happened with my Robo 3D Plus

    Hurray there is light at the end of the tunnel Robo has finally shipped out my board so in a few days i should be back in operation if nothing...
    Post by: Cuda70, Apr 18, 2016 in forum: Troubleshooting
  8. Cuda70
    Post

    Solved Something crazy just happened with my Robo 3D Plus

    Well i am not returning it as i like how it prints i have tried several programs and they are unable to locate the printer so i purchased a new...
    Post by: Cuda70, Apr 16, 2016 in forum: Troubleshooting
  9. Cuda70
    Post

    Solved Something crazy just happened with my Robo 3D Plus

    Well i have contacted Paypal asking for a refund as nobody from Robo has yet to contact me APR 09, 2016 | 12:49PM PDT Robo 3D Tech replied:...
    Post by: Cuda70, Apr 12, 2016 in forum: Troubleshooting
  10. Cuda70
    Post

    Solved Something crazy just happened with my Robo 3D Plus

    well i called and they are unable to answer my question about the missing board and have to send a request "upstairs"??? so i still have no answer...
    Post by: Cuda70, Apr 11, 2016 in forum: Troubleshooting
  11. Cuda70
    Post

    Solved Something crazy just happened with my Robo 3D Plus

    well i just give up time to pack this hunk of junk Robo 3D Plus up put it in the garage and call it a life lesson i have tried everything i can...
    Post by: Cuda70, Apr 8, 2016 in forum: Troubleshooting
  12. Cuda70
    Post

    Solved Something crazy just happened with my Robo 3D Plus

    Not Amazon bought right from Robo 3D company
    Post by: Cuda70, Apr 6, 2016 in forum: Troubleshooting
  13. Cuda70
    Post

    Solved Something crazy just happened with my Robo 3D Plus

    That was what i was thinking so i ordered a new arduino board and a extra hot end but my email says they(Robo) only shipped the hot end?? they...
    Post by: Cuda70, Apr 6, 2016 in forum: Troubleshooting
  14. Cuda70
    Post

    Solved Something crazy just happened with my Robo 3D Plus

    Did everything you asked and nothing when i plug in the USB i get the windows tone indicating that i plugged a USB item in or unplugged something...
    Post by: Cuda70, Apr 6, 2016 in forum: Troubleshooting
  15. Cuda70
    Post

    Solved Something crazy just happened with my Robo 3D Plus

    Great advice i will try this also thanks for the link and board info will keep you informed on my progress-THANKS :)
    Post by: Cuda70, Apr 6, 2016 in forum: Troubleshooting
  16. Cuda70
    Post

    Solved Something crazy just happened with my Robo 3D Plus

    Wow i cant believe with all the experienced people here not one answer not even a guess?? I am so stuck have tried everything but no luck :(
    Post by: Cuda70, Apr 6, 2016 in forum: Troubleshooting
  17. Cuda70
    Thread

    Solved Something crazy just happened with my Robo 3D Plus

    I was printing and it stopped feeding filament thinking i had a jam i checked but all was good. So i started to reinsert the fulfillment but it...
    Thread by: Cuda70, Apr 4, 2016, 31 replies, in forum: Troubleshooting
  18. Cuda70
    Post

    Refurbished R1 model sale. Good or Bad idea?

    Also if you have any problems the guys on the tech line are great Also check out Novice Experts videos on YouTube this guy is great These are...
    Post by: Cuda70, Mar 22, 2016 in forum: General Questions
  19. Cuda70
    Post

    Refurbished R1 model sale. Good or Bad idea?

    As a new Robo owner (two weeks) i would say to go for it the upgrades are easy to print and at the huge savings you can upgrade to a LCD board...
    Post by: Cuda70, Mar 21, 2016 in forum: General Questions
  20. Cuda70
    Post

    Experimenting with filament colorizing

    I like your idea it will be something cool to tinker with
    Post by: Cuda70, Mar 15, 2016 in forum: Show and Tell
Showing results 1 to 20 of 25 Next >
Search Again
Page 1 of 2