1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
  1. Yacobeeb
    Post

    Unresolved No power, now some power?

    Do you have a better ramps board recommendation than this?...
    Post by: Yacobeeb, Aug 7, 2019 in forum: Troubleshooting
  2. Yacobeeb
    Post

    Unresolved No power, now some power?

    how would you test if the ramps board works?
    Post by: Yacobeeb, Aug 7, 2019 in forum: Troubleshooting
  3. Yacobeeb
    Thread

    Unresolved No power, now some power?

    So I think I have made a great error. My Robo 3d r1 plus was working find beside a fan that went out. I had to re-solder on the older connector of...
    Thread by: Yacobeeb, Aug 6, 2019, 4 replies, in forum: Troubleshooting
  4. Yacobeeb
    Post

    Solved Robo 3D R1+ Ignores z-offsets

    I appreciate the reply. I think I didn't get a good download of the original firmware before I guess. Not knowing any better I thought one of the...
    Post by: Yacobeeb, Jul 26, 2019 in forum: Troubleshooting
  5. Yacobeeb
    Post

    Solved Robo 3D R1+ Ignores z-offsets

    I basically reflashed the firmware again to the ROBO3DR1PLUSV2 original Firmware and only used MatterControl to slice and set the z offset for my...
    Post by: Yacobeeb, Jul 25, 2019 in forum: Troubleshooting
  6. Yacobeeb
    Thread

    Solved Robo 3D R1+ Ignores z-offsets

    Hello everyone thanks in advance for the help! So I have this ROBO 3D printer for a few weeks now and can't for the life of me figure out why the...
    Thread by: Yacobeeb, Jul 25, 2019, 4 replies, in forum: Troubleshooting
  7. Yacobeeb
    Post

    Community Favorite Marlin 2.0.x release for Robo R1+

    Consider Cura gone. I am happy to start a new thread. This slamming into the bed issue has only happened on this Marlin Bug Fix 2.0 firmware. I...
    Post by: Yacobeeb, Jul 25, 2019 in forum: Mods and Upgrades
  8. Yacobeeb
    Post

    Community Favorite Marlin 2.0.x release for Robo R1+

    So here is what happened, sorry for it being a little long. I am open to trying pretty much anything. Not sure if I did something wrong or what...
    Post by: Yacobeeb, Jul 25, 2019 in forum: Mods and Upgrades
  9. Yacobeeb
    Post

    Community Favorite Marlin 2.0.x release for Robo R1+

    YAY HELP! :) thanks for the input guys! So it slammed down the extruder for a preloaded file in MatterControl 1.5 and a file I made it Cura. I...
    Post by: Yacobeeb, Jul 25, 2019 in forum: Mods and Upgrades
  10. Yacobeeb
    Post

    Community Favorite Marlin 2.0.x release for Robo R1+

    Just to clarify, The firmware did not work for me as I had hoped and I had issues with it. It fixed my z-offsets not being recognized but it made...
    Post by: Yacobeeb, Jul 25, 2019 in forum: Mods and Upgrades
  11. Yacobeeb
    Post

    Community Favorite Marlin 2.0.x release for Robo R1+

    Thanks for the reply buddy! I just wanted bradf80 too hear my experience with his firmware. Should I just like this this forum as a reference or...
    Post by: Yacobeeb, Jul 25, 2019 in forum: Mods and Upgrades
  12. Yacobeeb
    Post

    Community Favorite Marlin 2.0.x release for Robo R1+

    I am unable to link anything, unfortunately. But the thread that got me started here was labeled Marlin 1.1.9 Release for Robo R1+. Well, I...
    Post by: Yacobeeb, Jul 25, 2019 in forum: Mods and Upgrades
  13. Yacobeeb
    Post

    Community Favorite Marlin 2.0.x release for Robo R1+

    I certainly hope you are all still alive out here, haha. I have to start out by saying thank you all for supporting the Robo 3d community. If we...
    Post by: Yacobeeb, Jul 25, 2019 in forum: Mods and Upgrades
  14. Yacobeeb
    Post

    Community Favorite Marlin 2.0.x release for Robo R1+

    I just got finished typing out this list of my experience using this firmware and I keep getting my post labeled as spam(even with unlinking...
    Post by: Yacobeeb, Jul 25, 2019 in forum: Mods and Upgrades
Showing results 1 to 14 of 14
Search Again