1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 4 of 9
  1. joea
    Post

    Unresolved Calibration question

    Did you really mean MICRONS?
    Post by: joea, Aug 9, 2021 in forum: Troubleshooting
  2. joea
    Post

    Unresolved Calibration question

    You know, I did, sorta recently, change the linear bearings and maybe the rods. I'll have to check any records I may have. Was about the time I...
    Post by: joea, Aug 9, 2021 in forum: Troubleshooting
  3. joea
    Post

    Unresolved Calibration question

    This is where I am now. Even less? #define DEFAULT_MAX_FEEDRATE {500, 500, 5, 25} // (mm/sec) #define DEFAULT_MAX_ACCELERATION...
    Post by: joea, Aug 9, 2021 in forum: Troubleshooting
  4. joea
    Thread

    Partial Answer Matter Control V2x Windows Version?

    MC v2 claims Windows 10 is minimum. On a whim I installed it on Windows 7 . Rather than overwrite v 1.5, I installed it in a different location...
    Thread by: joea, Aug 9, 2021, 11 replies, in forum: General Questions
  5. joea
    Post

    Unresolved Calibration question

    Which way? I thought it was tight enough by "twanging" it.
    Post by: joea, Aug 9, 2021 in forum: Troubleshooting
  6. joea
    Post

    Unresolved Calibration question

    Most of the measurable overshoot seems to be in the Y axis. Could this be a belt tightness issue?
    Post by: joea, Aug 8, 2021 in forum: Troubleshooting
  7. joea
    Thread

    Unresolved Calibration question

    I found cylinders I print do not seem perfectly round. So, I printed the calibration cube. It is a bit difficult to measure due to the "over...
    Thread by: joea, Aug 8, 2021, 18 replies, in forum: Troubleshooting
  8. joea
    Post

    Solved matter control layer view

    For some reason mine does not show "sync to print". It used to be there. MC version is 1.5.0.
    Post by: joea, Aug 7, 2021 in forum: General Questions
  9. joea
    Post

    Solved Stops in middle of print "unable to communicate with Printer"

    It has not happened again (so far). I discounted it at first, but it may have been a power glitch caused by a make shift exhaust fan I had in a...
    Post by: joea, Aug 7, 2021 in forum: Troubleshooting
  10. joea
    Thread

    Solved matter control layer view

    After a long layoff, doing some printing. I swear I recall, in "layer view" I could see "real time" layers being printed. Now I do not, and...
    Thread by: joea, Aug 6, 2021, 3 replies, in forum: General Questions
  11. joea
    Thread

    Solved Stops in middle of print "unable to communicate with Printer"

    Using Matter control, Windows 7, twice now in longish prints has stopped dead, with the red led on the printer flashing madly, and MC saying it...
    Thread by: joea, Aug 6, 2021, 4 replies, in forum: Troubleshooting
  12. joea
    Thread

    Solved LCD screen power source

    Minor concern. Adding the LCD screen was fun. Not sure it really does anything useful, but it looks nice. However, as long as the USB cable is...
    Thread by: joea, Apr 5, 2021, 9 replies, in forum: General Questions
  13. joea
    Post

    Fan speed codes

    Changing the fan did the trick.
    Post by: joea, Jan 12, 2021 in forum: Software
  14. joea
    Thread

    Fan speed codes

    When attempting to test fan operation after installing a different parts cooling fan, I found the codes to turn the fan on and off. Worked fine...
    Thread by: joea, Jan 11, 2021, 2 replies, in forum: Software
  15. joea
    Thread

    Answered Terminal code error message

    Running test prints after changing hot end, see this frequently in print log: ******************************* ->N137 M105*3 [65.701]...
    Thread by: joea, Jan 11, 2021, 2 replies, in forum: Troubleshooting
  16. joea
    Post

    Community Favorite E3D v6 Information and Installation Guide

    I guess I was laboring under the delusion that Z offset would be reflected in the distance the nozzle is off the bed when "home". Apparently...
    Post by: joea, Jan 10, 2021 in forum: Mods and Upgrades
  17. joea
    Post

    Community Favorite E3D v6 Information and Installation Guide

    It does not seem to matter what Z offset I put in, after I Z home, the nozzle is still in contact with the bed.
    Post by: joea, Jan 10, 2021 in forum: Mods and Upgrades
  18. joea
    Post

    Community Favorite E3D v6 Information and Installation Guide

    Does not seem to be having desired effect. From Z "home" I have to go +Z a few tenths of a mm to get a sheet of paper under the nozzle.
    Post by: joea, Jan 10, 2021 in forum: Mods and Upgrades
  19. joea
    Post

    Community Favorite E3D v6 Information and Installation Guide

    Pretty sure it is a "glass" bed.
    Post by: joea, Jan 10, 2021 in forum: Mods and Upgrades
  20. joea
    Post

    Community Favorite E3D v6 Information and Installation Guide

    I was really worried about the mechanical differences and destroying the nozzle or bed but I guess that is unlikely as the carriage will just "sit...
    Post by: joea, Jan 10, 2021 in forum: Mods and Upgrades
Showing results 61 to 80 of 171 Next >
Search Again
Page 4 of 9