1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
  1. ErnieN
    Post

    BuildTac FlexPlate on V2 bed?

    Anybody try white buildtak on the R2? I think it should just work, but I've had issues where shiny glue was causing issues with auto-leveling before.
    Post by: ErnieN, Dec 4, 2018 in forum: Mods and Upgrades
  2. ErnieN
    Post

    BuildTac FlexPlate on V2 bed?

    Yeah, the 8.66x8.66 is what I needed. Thanks!
    Post by: ErnieN, Nov 12, 2018 in forum: Mods and Upgrades
  3. ErnieN
    Post

    BuildTac FlexPlate on V2 bed?

    [ATTACH] Hey, I just got an 8x8 Flexplate from MatterHackers (Robo3D always seem to be out of stock). It doesn't fit like the videos here that...
    Post by: ErnieN, Nov 10, 2018 in forum: Mods and Upgrades
  4. ErnieN
    Thread

    I now have to print my PLA using ABS settings since upgrading to Olsson Ruby

    If I use PLA settings it comes out stringy and doesn't adhere well. Apparently 190C isn't enough to melt the PLA sufficiently. But all is ok if...
    Thread by: ErnieN, Jul 13, 2018, 3 replies, in forum: Mods and Upgrades
  5. ErnieN
    Post

    Has anyone had success with magigoo?

    Apparently the trick is to let it dry for at least 20 minutes before printing. Then it works much like a glue stick but I noticed it's much...
    Post by: ErnieN, Jun 6, 2018 in forum: General Questions
  6. ErnieN
    Thread

    Has anyone had success with magigoo?

    I’ve tried using it to improve bed adhesion on my R2 but it seems to do the opposite. Even the smallest amount of the stuff feels like an...
    Thread by: ErnieN, May 19, 2018, 4 replies, in forum: General Questions
  7. ErnieN
    Post

    Dual Extruder Kit Updates?

    Say, if any Palette+ users are tired of using the box it came in as a spool holder, I’ve designed my own spool holder just for it at Thingiverse,...
    Post by: ErnieN, Apr 11, 2018 in forum: Mods and Upgrades
  8. ErnieN
    Post

    Dual Extruder Kit Updates?

    But that's not the case with dual extruders, right? I mean you just stop extruding white on one extruder and start extruding black on the second...
    Post by: ErnieN, Apr 11, 2018 in forum: Mods and Upgrades
  9. ErnieN
    Post

    Dual Extruder Kit Updates?

    No difference printwise, but it pauses for a few seconds whenever a splice is made. I suppose it would make a difference with hundreds of...
    Post by: ErnieN, Apr 11, 2018 in forum: Mods and Upgrades
  10. ErnieN
    Post

    Dual Extruder Kit Updates?

    I've been using a Palette+ for quite a while. Side transitions don't work for the C2 or R2, not sure about the R1. I played around with variable...
    Post by: ErnieN, Mar 31, 2018 in forum: Mods and Upgrades
  11. ErnieN
    Thread

    Lost my R2 stylus, is there a model for printing a new one?

    I already have conductive filament and printed a few replacement styluses from models I found on the internet, but I prefer the one that came with...
    Thread by: ErnieN, Mar 31, 2018, 10 replies, in forum: General Questions
Showing results 1 to 11 of 11
Search Again