1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 2 of 3
  1. wuidling
    Thread

    Z-Axis

    I have seen that on the top of the Z-Axis is no nut or bearing. Right or wrong ? Regards
    Thread by: wuidling, Jul 20, 2020, 4 replies, in forum: General Questions
  2. wuidling
    Post

    My solution for the IR sensor / Buildtak probe failures

    I found this in the RepRap Forum: https://reprap.org/forum/read.php?340,486842 another solution could be buying a flexplate and blue tape. Regards
    Post by: wuidling, Jul 6, 2020 in forum: Troubleshooting
  3. wuidling
    Post

    My solution for the IR sensor / Buildtak probe failures

    Buildtalk dont work witht the Robo R2 IR sensor.. Anyway you will get much better results with manual leveling. The Buildtalk Flexplate and...
    Post by: wuidling, Jul 6, 2020 in forum: Troubleshooting
  4. wuidling
    Post

    Power Supply

    Shame on me ! After checking the power supply and changing the 40W Heater back to at 30W the problem still exists and so I started from the...
    Post by: wuidling, Jun 30, 2020 in forum: Troubleshooting
  5. wuidling
    Post

    Power Supply

    Last day a print without heating bed was s successful. Actually the printer stops (complete shutdown and restart) in different cases: Heating...
    Post by: wuidling, Jun 19, 2020 in forum: Troubleshooting
  6. wuidling
    Post

    Power Supply

    Voltage 4,84 11,80 23,47 Power Supply cool. Will check this with Heating. Thanks
    Post by: wuidling, Jun 17, 2020 in forum: Troubleshooting
  7. wuidling
    Thread

    Power Supply

    After a lot of beginner problems i found the power supply as a reason for some undefinied errors. In some cases the printer suddendly makes a...
    Thread by: wuidling, Jun 16, 2020, 11 replies, in forum: Troubleshooting
  8. wuidling
    Post

    Is the E3D V6 compatible with R2?

    Hello, So i see no holes in the stl, you use the fan mounted on the hotend ? Thanks for the Thingiverse Work. Do you have a picture ? Regards
    Post by: wuidling, May 4, 2020 in forum: General Questions
  9. wuidling
    Post

    ROBO R2 Installation

    Alles in allem ein cooles Hobby. Bis zum ersten sauberen Druck dauerts leider lang. Vielleicht ein parr wichtigsten Sachen nochmal : 1. Das...
    Post by: wuidling, Apr 25, 2020 in forum: Germany
  10. wuidling
    Post

    Robo R2 Z Wizard wont calibrate correctly

    Thanks, this is what I`'am looking for. Unfortunately i did not find it so i give it back after 1 Day. Regards
    Post by: wuidling, Apr 23, 2020 in forum: Troubleshooting
  11. wuidling
    Post

    Robo R2 Z Wizard wont calibrate correctly

    I prefer after days of testing and also damaging the print surface the following calibration steps. Make the Z-Offset Calibration and let 5 mm...
    Post by: wuidling, Apr 21, 2020 in forum: Troubleshooting
  12. wuidling
    Post

    Z-Offset Wizard stuck at step 1 of 4

    Sorry for this misunderstanding, i mean in Cura the settings for the support. (Enable Support Interface) The prints in low quality are very rough...
    Post by: wuidling, Apr 14, 2020 in forum: Troubleshooting
  13. wuidling
    Post

    ROBO R2 Installation

    Update, bei mir gibts aktuell noch ein Problem mit dem Auto Bed Leveling GCode G29. Ihr könnt Befehle ausschalten mit einem Semikolon. Also ;...
    Post by: wuidling, Apr 14, 2020 in forum: Germany
  14. wuidling
    Post

    Z-Offset Wizard stuck at step 1 of 4

    Thanks for this interesting feature. Will try it. By the way do you have working adjustments for the enabled support interface. Regards
    Post by: wuidling, Apr 14, 2020 in forum: Troubleshooting
  15. wuidling
    Post

    ROBO R2 Installation

    Anbei mal ein paar Testdrucke mit geringer Qualität.
    Post by: wuidling, Apr 12, 2020 in forum: Germany
  16. wuidling
    Post

    ROBO R2 Installation

    SD Karte austauschen Befindet sich unten im Gehäuse.. Auf der Unterseite des Raspi wo die grüne LED blinkt.. Ihr benötigt ein Imager z.B....
    Post by: wuidling, Apr 12, 2020 in forum: Germany
  17. wuidling
    Post

    Z-Offset Wizard stuck at step 1 of 4

    Yes, printed wirh Cura 20% Infill, 70mm Speed, Low Quality, PET 235° The file is from Thingiverse. Regards
    Post by: wuidling, Apr 12, 2020 in forum: Troubleshooting
  18. wuidling
    Post

    Z-Offset Wizard stuck at step 1 of 4

    At least the Robo worked almost perfect, but the Fine Offset Wizard do not work at all. The values generated in the menu make no sense. So i make...
    Post by: wuidling, Apr 11, 2020 in forum: Troubleshooting
  19. wuidling
    Post

    ROBO R2 Installation

    Bin über ein weiteren Anwenderfehler gestolpert. Wenn ihr mit Cura das Modell zum Octoprint schickt werden sowohl die Startparameter der Cura...
    Post by: wuidling, Apr 7, 2020 in forum: Germany
  20. wuidling
    Post

    GCode (Newbie)

    Thanks, for a Newbie its a little bit difficult to handle all these adjustments. You're looking to a resetting printer and again the search...
    Post by: wuidling, Apr 6, 2020 in forum: Troubleshooting
Showing results 21 to 40 of 56 Next >
Search Again
Page 2 of 3