1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 3 of 3
  1. Frank van Gilluwe
    Post

    Pushing the edge of print volume

    Thanks for the blogs! Hoping my front magnetic cover/door project will help reduce curling too. Printed all the parts (7). I was almost finished...
    Post by: Frank van Gilluwe, Oct 2, 2017 in forum: General Questions
  2. Frank van Gilluwe
    Post

    Pushing the edge of print volume

    Another note - I think the clips will work better if they attached to the bottom of the plastic bed rather than the aluminum plate. This should...
    Post by: Frank van Gilluwe, Sep 30, 2017 in forum: General Questions
  3. Frank van Gilluwe
    Post

    Pushing the edge of print volume

    @OutsourcedGuru - Funny - I thought of a similar idea. I think the aluminum may be too thick and/or difficult to bend without breaking. I think...
    Post by: Frank van Gilluwe, Sep 30, 2017 in forum: General Questions
  4. Frank van Gilluwe
    Post

    Pushing the edge of print volume

    I have similar curling problem printing a box that is at the limit of the printer (114mm x 114mm) a little smaller than I really want, but I'll...
    Post by: Frank van Gilluwe, Sep 30, 2017 in forum: General Questions
  5. Frank van Gilluwe
    Post

    Faster startup with 24v

    Checked my C2 extruder - 13.4 ohms. At 19V this would be a 27W unit. At 24V, this would be a 43W unit. Neither fits into some nice standard, but...
    Post by: Frank van Gilluwe, Sep 29, 2017 in forum: Mods and Upgrades
  6. Frank van Gilluwe
    Post

    Faster startup with 24v

    Being a resistive element, if the C2 really is 19V, using 24V is only 25% increase. I doubt it makes any significant difference. The heat is...
    Post by: Frank van Gilluwe, Sep 29, 2017 in forum: Mods and Upgrades
  7. Frank van Gilluwe
    Post

    Faster startup with 24v

    I'm not sure - there are no markings on the extruder. I sort of assumed Robo would use the same extruders in the R2 as the C2, and therefore it's...
    Post by: Frank van Gilluwe, Sep 28, 2017 in forum: Mods and Upgrades
  8. Frank van Gilluwe
    Thread

    Faster startup with 24v

    While the C2 uses a 19V transformer, I think the R2 uses a 24v transformer. The main electronics board appears to be the same for the C2 and R2....
    Thread by: Frank van Gilluwe, Sep 28, 2017, 26 replies, in forum: Mods and Upgrades
  9. Frank van Gilluwe
    Post

    Changing filament mid print

    I wrote up a complete step-by-step process for the C2, with screen shots, so that no manual gcode changes are necessary. Works perfectly - just...
    Post by: Frank van Gilluwe, Sep 28, 2017 in forum: General Questions
  10. Frank van Gilluwe
    Post

    Filament Feed Tube Clips

    Perhaps a stupid question, but what do you use these clips for? I can't see any purpose for them.
    Post by: Frank van Gilluwe, Sep 28, 2017 in forum: Mods and Upgrades
  11. Frank van Gilluwe
    Post

    Answered Inoperative C2 filament run-out switch

    I wonder which is the newer design - switch or optical? While my unit was purchased new about 2 weeks ago, the newest file on the SC card (before...
    Post by: Frank van Gilluwe, Sep 28, 2017 in forum: Troubleshooting
  12. Frank van Gilluwe
    Post

    Answered Inoperative C2 filament run-out switch

    My filament switch was open from day one. I got no continuity at the black Raspberry 40-pin connector between the red and black wires. I pulled...
    Post by: Frank van Gilluwe, Sep 27, 2017 in forum: Troubleshooting
Find older messages
Showing results 41 to 52 of 52
Search Again
Page 3 of 3