1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 2 of 2
  1. Michele Beyer
    Post

    Partially Solved Calibrating seems to be off on Y axis

    So what is the actual solution here? I'm printing a large print and since part of it prints out of the heated area, eventually it starts pulling...
    Post by: Michele Beyer, May 22, 2016 in forum: Troubleshooting
  2. Michele Beyer
    Post

    Answered Max Temp for heat bed? 80??!!

    Alright!! I've had the bed sitting at 115 for the past 30 min and no error message!!! Thank you all again - this is great!!
    Post by: Michele Beyer, May 21, 2016 in forum: Troubleshooting
  3. Michele Beyer
    Post

    Answered Max Temp for heat bed? 80??!!

    Should I turn off Matter Control? I actually have my printer on right now, heated and ready to go.......
    Post by: Michele Beyer, May 21, 2016 in forum: Troubleshooting
  4. Michele Beyer
    Post

    Answered Max Temp for heat bed? 80??!!

    Well, I thought I was good.........but I received this error message during the upload: avrdude: ser_drain(): read error: The handle is invalid.
    Post by: Michele Beyer, May 21, 2016 in forum: Troubleshooting
  5. Michele Beyer
    Post

    Answered Max Temp for heat bed? 80??!!

    Ok, I'll finish the video and I've subscribed to his YouTube channel. Thank you all for your help, I really appreciate it!!! Enjoy your weekend!!
    Post by: Michele Beyer, May 21, 2016 in forum: Troubleshooting
  6. Michele Beyer
    Post

    Answered Max Temp for heat bed? 80??!!

    Ok got it, I've edited the print bed temp - now how do I upload that to matter control?
    Post by: Michele Beyer, May 21, 2016 in forum: Troubleshooting
  7. Michele Beyer
    Post

    Answered Max Temp for heat bed? 80??!!

    So, I guess I'm still a little confused - am I supposed to download arduino and the autolevel firmware?
    Post by: Michele Beyer, May 21, 2016 in forum: Troubleshooting
  8. Michele Beyer
    Post

    Answered Max Temp for heat bed? 80??!!

    I have the Robo 3D R1, it has a ribbon cable to the bed.
    Post by: Michele Beyer, May 21, 2016 in forum: Troubleshooting
  9. Michele Beyer
    Post

    Answered Max Temp for heat bed? 80??!!

    So do I solve this issue in the same manner?
    Post by: Michele Beyer, May 21, 2016 in forum: Troubleshooting
  10. Michele Beyer
    Post

    Answered Max Temp for heat bed? 80??!!

    I'm not a software person - so you may have to explain a little bit more - am i supposed to follow the "flashing the firmware" steps posted on the...
    Post by: Michele Beyer, May 21, 2016 in forum: Troubleshooting
  11. Michele Beyer
    Post

    Answered Max Temp for heat bed? 80??!!

    It literally just happened to me again :-) (I've attached an image to make sure I'm talking about the same error as everybody else)
    Post by: Michele Beyer, May 21, 2016 in forum: Troubleshooting
  12. Michele Beyer
    Post

    Answered Max Temp for heat bed? 80??!!

    So how do you change the firmware? When I print ABS at work (we have a makerbot and a couple lulzbot taz5's) I always have the bed at 115 and my...
    Post by: Michele Beyer, May 21, 2016 in forum: Troubleshooting
Find older messages
Showing results 21 to 32 of 32
Search Again
Page 2 of 2