1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
  1. Reece Markowsky
    Post

    R2 slipping for a specific spool of filament

    That did the trick! [emoji95] thanks !! Sent from my iPhone using Tapatalk
    Post by: Reece Markowsky, Aug 26, 2018 in forum: Troubleshooting
  2. Reece Markowsky
    Thread

    R2 slipping for a specific spool of filament

    It seems my filament is slipping and it causing bad prints. It’s even slipping periodically/frequently during filament load. I’ve uploaded a video...
    Thread by: Reece Markowsky, Aug 25, 2018, 2 replies, in forum: Troubleshooting
  3. Reece Markowsky
    Thread

    Nothing sliced with Cura is printing on the R2

    Hi. I am unable to get anything to print properly that has been slided by Cura for Robo, OctoPrint and the R2. If i print the files that came...
    Thread by: Reece Markowsky, Jul 7, 2018, 8 replies, in forum: Troubleshooting
  4. Reece Markowsky
    Post

    Partial Answer Extruding Issue I guess?

    Is this occurring on all models, different PLA spools too? I.e have you eliminated most other possibilities? Sent from my iPhone using Tapatalk
    Post by: Reece Markowsky, Jul 7, 2018 in forum: Troubleshooting
  5. Reece Markowsky
    Post

    Robo R2 Connection Interrupted after update?

    Done and working! Thanks so much Mark!
    Post by: Reece Markowsky, Jul 6, 2018 in forum: Troubleshooting
  6. Reece Markowsky
    Post

    Robo R2 Connection Interrupted after update?

    Thank you. Yes, I also logged a ticket with support for this, so I will update that ticket requesting an image. Much appreciated!
    Post by: Reece Markowsky, Jul 3, 2018 in forum: Troubleshooting
  7. Reece Markowsky
    Thread

    Robo R2 Connection Interrupted after update?

    I just loaded new filament into the Robo R2 (filament change wizard). shortly after that, I the R2 did a software update (on its own). After the...
    Thread by: Reece Markowsky, Jul 3, 2018, 5 replies, in forum: Troubleshooting
  8. Reece Markowsky
    Post

    Solved Why are my prints coming out like this?!

    Glad to hear! Sent from my iPhone using Tapatalk
    Post by: Reece Markowsky, Jun 25, 2018 in forum: Troubleshooting
  9. Reece Markowsky
    Post

    Answered Extruder Stalls and clicks in certain Y location consistently

    Is it always the same model or all models? If it’s same print sounds like maybe slicing? Try reslicing it? Sent from my iPhone using Tapatalk
    Post by: Reece Markowsky, Jun 23, 2018 in forum: Troubleshooting
  10. Reece Markowsky
    Post

    Solved Why are my prints coming out like this?!

    Oh my apologies. I thought C2. So assumed you have cleaned the feeder gear and ensured the hobbed bolt is tight as it should be then.
    Post by: Reece Markowsky, Jun 22, 2018 in forum: Troubleshooting
  11. Reece Markowsky
    Post

    Solved Why are my prints coming out like this?!

    [IMG] This is a pic of the feeder job bolt. You can see the tiny screw. If it’s even a bit loose the bolt won’t be tightly aligned (pushed in as...
    Post by: Reece Markowsky, Jun 22, 2018 in forum: Troubleshooting
  12. Reece Markowsky
    Post

    Solved Why are my prints coming out like this?!

    check your feeder bolt, the tiny screw that holds it in tight may be loose. i have seen my prints look like this along with ticking noises. once...
    Post by: Reece Markowsky, Jun 22, 2018 in forum: Troubleshooting
  13. Reece Markowsky
    Post

    Clicking sound

    I wanted to share the source of a problem I encountered when I had clicking. it was very frustrating as nothing I seemed to try worked and of...
    Post by: Reece Markowsky, Jun 22, 2018 in forum: Troubleshooting
Showing results 1 to 13 of 13
Search Again