1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 1 of 5
  1. Cbrown
    Post

    E3D v6 Information, Installation Guides, and Review

    I was just going to use my robo thermistor. Is there any adjustments from the larger fan on the hotend?
    Post by: Cbrown, Aug 6, 2016 in forum: Mods and Upgrades
  2. Cbrown
    Post

    E3D v6 Information, Installation Guides, and Review

    If I have a R1+ and I use all the same existing robo components on the e3d do I need to make the arudino code changes?
    Post by: Cbrown, Aug 6, 2016 in forum: Mods and Upgrades
  3. Cbrown
    Post

    Solved Hobbed Drive Gear

    It makes sense. I can't take mine off right now but I can see how this is the right bolt. I was wondering about the assembly but this makes sense.
    Post by: Cbrown, Jul 11, 2016 in forum: Troubleshooting
  4. Cbrown
    Post

    Solved Hobbed Drive Gear

    Oh okay, thanks!
    Post by: Cbrown, Jul 11, 2016 in forum: Troubleshooting
  5. Cbrown
    Post

    Solved Hobbed Drive Gear

    Just m8 nor mk8?
    Post by: Cbrown, Jul 11, 2016 in forum: Troubleshooting
  6. Cbrown
    Post

    Solved Hobbed Drive Gear

    It looks more like this
    Post by: Cbrown, Jul 11, 2016 in forum: Troubleshooting
  7. Cbrown
    Post

    Solved Hobbed Drive Gear

    I am printing right now so I can't take a photo. It's where you insert the filament just below the lever on the rope side.
    Post by: Cbrown, Jul 11, 2016 in forum: Troubleshooting
  8. Cbrown
    Post

    Solved Hobbed Drive Gear

    Mine is warn down
    Post by: Cbrown, Jul 11, 2016 in forum: Troubleshooting
  9. Cbrown
    Post

    Solved Hobbed Drive Gear

    Gear
    Post by: Cbrown, Jul 11, 2016 in forum: Troubleshooting
  10. Cbrown
    Thread

    Solved Hobbed Drive Gear

    I need to replace my hobbed drive gear, does anyone know if it's MK7, MK8?
    Thread by: Cbrown, Jul 11, 2016, 13 replies, in forum: Troubleshooting
  11. Cbrown
    Thread

    Flexible Filament

    This any any mobs you can make to the standard assembly to print flexible filament easier without buying a e3d or etc.
    Thread by: Cbrown, Jul 9, 2016, 4 replies, in forum: General Questions
  12. Cbrown
    Thread

    Unresolved Nozzle temp drops

    I have started to have a problem with the hotend holding a consistent temperature during prints at 215c. Its heats up, starts the print then falls...
    Thread by: Cbrown, Jun 8, 2016, 3 replies, in forum: Troubleshooting
  13. Cbrown
    Post

    Atlanta - ColorFabb Event

    The event has been planned for June 27th if you are interested. here is the link to register:...
    Post by: Cbrown, Jun 8, 2016 in forum: Off Topic
  14. Cbrown
    Post

    Atlanta - ColorFabb Event

    The event has been planned for June 27th if you are interested. Here is a link to register;...
    Post by: Cbrown, Jun 8, 2016 in forum: Off Topic
  15. Cbrown
    Post

    Solved Z-Axis is out of wack

    Absolutely right!
    Post by: Cbrown, Jun 6, 2016 in forum: Troubleshooting
  16. Cbrown
    Post

    Solved Z-Axis is out of wack

    They are both on the outer prongs. All three are on the outer prongs
    Post by: Cbrown, Jun 6, 2016 in forum: Troubleshooting
  17. Cbrown
    Post

    Solved Z-Axis is out of wack

    Here are the switches
    Post by: Cbrown, Jun 6, 2016 in forum: Troubleshooting
  18. Cbrown
    Post

    Solved Z-Axis is out of wack

    There are 3 switches total. I have tripled checked the switches.
    Post by: Cbrown, Jun 6, 2016 in forum: Troubleshooting
  19. Cbrown
    Post

    Solved Z-Axis is out of wack

    Yes. The switches are exactly as they have been sense day 1. I checked
    Post by: Cbrown, Jun 6, 2016 in forum: Troubleshooting
  20. Cbrown
    Post

    Solved Z-Axis is out of wack

    I have checked all of the switches and nothing has been disconnected
    Post by: Cbrown, Jun 6, 2016 in forum: Troubleshooting
Showing results 1 to 20 of 94 Next >
Search Again
Page 1 of 5