1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 2 of 2
  1. racer
    Post

    Repurposing Pirate3d Buccaneer

    Hi Dragonsquirrel, The full set of buccaneer-gcode is located in a file in the root directory of the buccaneer. The file is called...
    Post by: racer, Jan 6, 2019 in forum: Off Topic
  2. racer
    Post

    Repurposing Pirate3d Buccaneer

    OK guys, I did it! I brainwashed my Buccaneer :) using the original hardware! Now it runs on Octoprint with Marlin FW :) I still need to tweak...
    Post by: racer, Jan 6, 2019 in forum: Off Topic
  3. racer
    Post

    Repurposing Pirate3d Buccaneer

    Hi, The last couple of days I have been analyzing the Buccaneer Logic Board 1.0 Rev C PRD. My goal is to flash Marlin FW onto the ATMEGA1284P...
    Post by: racer, Jan 4, 2019 in forum: Off Topic
  4. racer
    Post

    Repurposing Pirate3d Buccaneer

    Well done! Hopefully we can make some progress now. Does someone have the Marlin Firmware for the Buccaneer?
    Post by: racer, Feb 28, 2018 in forum: Off Topic
  5. racer
    Post

    Repurposing Pirate3d Buccaneer

    I was able to read the settings from the original Buccaneer Firmware: Steps per unit: X=80.0000 Y=80.0000 Z=1600.0000 E=115.0000 Maximum...
    Post by: racer, Dec 30, 2017 in forum: Off Topic
  6. racer
    Post

    Repurposing Pirate3d Buccaneer

    What are these switches for? [ATTACH]
    Post by: racer, Dec 29, 2017 in forum: Off Topic
  7. racer
    Post

    Repurposing Pirate3d Buccaneer

    What I did to get SSH root access was the following: Take the SD card from the Buccaneer, make a copy, use the copy to experiment. I copied my...
    Post by: racer, Dec 26, 2017 in forum: Off Topic
  8. racer
    Post

    Repurposing Pirate3d Buccaneer

    I‘m working on this now. My goal is to get Octo-Print working on the original hardware with The Marlin firmware.
    Post by: racer, Dec 26, 2017 in forum: Off Topic
  9. racer
    Post

    Repurposing Pirate3d Buccaneer

    Me 2 or even 250000, but the Buccaneer has an ATMega 1284p which runs appaerently better at 38400. In case you use Linux, could you maybe run the...
    Post by: racer, Dec 25, 2017 in forum: Off Topic
  10. racer
    Post

    Repurposing Pirate3d Buccaneer

    I can now read the serial line, but I don't think I've got the correct serial settings yet as there is still some gibberish at the end of every...
    Post by: racer, Dec 23, 2017 in forum: Off Topic
  11. racer
    Post

    Repurposing Pirate3d Buccaneer

    Thank you, download & installation worked!
    Post by: racer, Dec 23, 2017 in forum: Off Topic
  12. racer
    Post

    Repurposing Pirate3d Buccaneer

    That's just the beginning, I'm looking for the commands to load / eject filament, auto-levelling etc. I mounted a serial rx on the hardware...
    Post by: racer, Dec 23, 2017 in forum: Off Topic
  13. racer
    Post

    Repurposing Pirate3d Buccaneer

    the Pirated 3D website is offline, does someone have the original buccaneer windows software (need it for reverse enginering). I'm trying to...
    Post by: racer, Dec 23, 2017 in forum: Off Topic
Find older messages
Showing results 21 to 33 of 33
Search Again
Page 2 of 2