1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 2 of 4
  1. Scifideity
    Post

    Solved At my wits end. Need help w/ firmware

    Hi Mark, Got the boards swapped out. Went ahead and swapped the Arduino, RAMPS, and Stepper Drivers. Installed the ROBO3DR1PLUSV2 firmware and...
    Post by: Scifideity, Oct 8, 2021 in forum: Troubleshooting
  2. Scifideity
    Post

    Solved At my wits end. Need help w/ firmware

    Cool. Spare parts are always a good thing. :D Just ordered the kit and it should be here Thursday. If all goes well I'll have this printer up...
    Post by: Scifideity, Oct 5, 2021 in forum: Troubleshooting
  3. Scifideity
    Post

    Solved At my wits end. Need help w/ firmware

    Hi Mark, So far I've replaced the thermistor and hot end heater element, multiple different USB cables, and printed via USB and via Octoprint....
    Post by: Scifideity, Oct 5, 2021 in forum: Troubleshooting
  4. Scifideity
    Post

    Solved At my wits end. Need help w/ firmware

    My default method of printing is usually via gcode uploaded to Octoprint. Currently I'm troubleshooting with direct Mac to Printer connection via...
    Post by: Scifideity, Oct 4, 2021 in forum: Troubleshooting
  5. Scifideity
    Post

    Solved At my wits end. Need help w/ firmware

    Hi Mark, I ran another test after moving the printer closer to my Mac and switching to a brand new USB cable. Log file attached. You can see...
    Post by: Scifideity, Oct 4, 2021 in forum: Troubleshooting
  6. Scifideity
    Post

    Solved At my wits end. Need help w/ firmware

    Hi Mark, Doesn't look like either part was the culprit. I was hoping one of them would have been defective and the solution but the e3Dv6 hot...
    Post by: Scifideity, Oct 4, 2021 in forum: Troubleshooting
  7. Scifideity
    Post

    Solved At my wits end. Need help w/ firmware

    Thanks Mark. Some additional info : It dawned on me the 3DBenchy test file was a common denominator so I tried another file last night to...
    Post by: Scifideity, Oct 1, 2021 in forum: Troubleshooting
  8. Scifideity
    Post

    Solved At my wits end. Need help w/ firmware

    Forgot to mention. The test print in the previous post video ran for over 10min before the error occurred. I've also attempted to go back to the...
    Post by: Scifideity, Sep 30, 2021 in forum: Troubleshooting
  9. Scifideity
    Thread

    Solved At my wits end. Need help w/ firmware

    Greetings Programs, Apologies for the lengthy post, trying to get as much info presented as I can to hopefully help spark a recognition in...
    Thread by: Scifideity, Sep 30, 2021, 52 replies, in forum: Troubleshooting
  10. Scifideity
    Post

    Filament Runout Sensor (FRS) upgrade to Robo R1/R1+

    Thanks! I did change the pins_RAMPS.h as shown in the guide to pin 20. I got busy and paused messing with it but will try to get it tested out...
    Post by: Scifideity, Jul 20, 2020 in forum: Mods and Upgrades
  11. Scifideity
    Post

    Filament Runout Sensor (FRS) upgrade to Robo R1/R1+

    Are the code modifications required for this sensor already built into Marlin 1.1.9 ? I'm finding very similar entries but not a 1:1 match. I'm...
    Post by: Scifideity, Jul 18, 2020 in forum: Mods and Upgrades
  12. Scifideity
    Post

    glue or tape?

    I've used the large Elmer's purple glue sticks since I got the printer and haven't had any issues once the printer was dialed in. Works like a...
    Post by: Scifideity, Jul 17, 2017 in forum: General Questions
  13. Scifideity
    Post

    Cura Users - Which version are you using?

    I had my Robo R1+ setup in 2.1 and got sidetracked and just kept using 15.04.6. I lost everything configured in 2.1 when upgrading to 2.3.1....
    Post by: Scifideity, Nov 14, 2016 in forum: Software
  14. Scifideity
    Post

    Cura 2.1 Beta

    Thanks for putting these files together. :) The only thing I think i see that needs tweaking in the .json file is the height should be 210 right?...
    Post by: Scifideity, Jun 27, 2016 in forum: Software
  15. Scifideity
    Post

    Great new slicer software, Craftware.

    I'm working on the theory that it's just another slicer and we just need to configure our build volume, printer specs, and put in the Start and...
    Post by: Scifideity, May 24, 2016 in forum: Software
  16. Scifideity
    Post

    Great new slicer software, Craftware.

    Apologies for raising a necrothread from the dead but I just stumbled across Craftware at the recommendation of Lilykill. I see the config...
    Post by: Scifideity, May 20, 2016 in forum: Software
  17. Scifideity
    Post

    Web enabled Robo3d using Raspberry Pi and Octoprint

    I used Tom's link which took me to the Pi 2 Model B 1GB 900MHz which I think it the last one before Pi 3 but i'm not positive. So far I have no...
    Post by: Scifideity, Apr 22, 2016 in forum: Mods and Upgrades
  18. Scifideity
    Post

    Web enabled Robo3d using Raspberry Pi and Octoprint

    Anyone find and implement a good solution for adding external Status LEDs to their Pi once it's in a case?
    Post by: Scifideity, Apr 20, 2016 in forum: Mods and Upgrades
  19. Scifideity
    Post

    Web enabled Robo3d using Raspberry Pi and Octoprint

    I'm experiencing similar results, minus the crashing bit, using this new Pi 2 board. Copied an 11.5Meg .gcode file in about 5sec and a fresh copy...
    Post by: Scifideity, Apr 18, 2016 in forum: Mods and Upgrades
  20. Scifideity
    Post

    Web enabled Robo3d using Raspberry Pi and Octoprint

    First impressions on the new Pi 2. I ordered a different Wifi dongle for this one just to rule out the WiPi and the new Pi 2 and Wifi fired right...
    Post by: Scifideity, Apr 18, 2016 in forum: Mods and Upgrades
Showing results 21 to 40 of 75 Next >
Search Again
Page 2 of 4