1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 3 of 3
  1. SPyKER
    Post

    Kickstarter Edition: Full rebuild help

    I got them today and drilled them. They are installed now. The lower is now put back together, says the bed. Cutting GT2 to replace now. [IMG]...
    Post by: SPyKER, Apr 3, 2017 in forum: Mods and Upgrades
  2. SPyKER
    Post

    Partial Answer First Gen ROBO printer

    [IMG] Lower level put back together... Sent from my LG-LS997 using Tapatalk
    Post by: SPyKER, Apr 3, 2017 in forum: Troubleshooting
  3. SPyKER
    Post

    Y-axis drawer slide replacement options?

    I also saw this: http://www.thingiverse.com/thing:211965 I was thinking that I could take the dimensions of that baseplate with two holes, create...
    Post by: SPyKER, Apr 3, 2017 in forum: Mods and Upgrades
  4. SPyKER
    Thread

    Y-axis drawer slide replacement options?

    I know they are out there, but what is the most reliable replacement? I should be completing the rebuild this week, and that is going to be one of...
    Thread by: SPyKER, Apr 3, 2017, 4 replies, in forum: Mods and Upgrades
  5. SPyKER
    Post

    Kickstarter Edition: Full rebuild help

    [ATTACH] Polishing the rods with 2500 grit and olive oil. Filed down the rough cut ends first. They're so much smoother now, like glass compared...
    Post by: SPyKER, Mar 31, 2017 in forum: Mods and Upgrades
  6. SPyKER
    Thread

    So this happened today...

    [ATTACH]
    Thread by: SPyKER, Mar 30, 2017, 2 replies, in forum: Off Topic
  7. SPyKER
    Post

    Community Favorite Alternative to the Lead Screw Upgrade Kit

    And?
    Post by: SPyKER, Mar 30, 2017 in forum: Mods and Upgrades
  8. SPyKER
    Post

    Kickstarter Edition: Full rebuild help

    I did today, and was very cordial as I have never before this point talked down about Robo #D or the printer. I just am tired or attending the...
    Post by: SPyKER, Mar 30, 2017 in forum: Mods and Upgrades
  9. SPyKER
    Post

    Kickstarter Edition: Full rebuild help

    The drawer slides are also sticking a bit. Just blow them off with pressure and re-oil them?
    Post by: SPyKER, Mar 29, 2017 in forum: Mods and Upgrades
  10. SPyKER
    Post

    Kickstarter Edition: Full rebuild help

    Would you be kind enough to print out the left and right of these? They look a bit stronger and I like the idea of the micro switch holder off the...
    Post by: SPyKER, Mar 29, 2017 in forum: Mods and Upgrades
  11. SPyKER
    Post

    Kickstarter Edition: Full rebuild help

    I haven't yet. And I figured out partially why it was making odd noises, and not printing right: The bottom belt has dry rot, and one of the...
    Post by: SPyKER, Mar 29, 2017 in forum: Mods and Upgrades
  12. SPyKER
    Post

    Kickstarter Edition: Full rebuild help

    What I was implying was that I wanted Robo 3D to exchange my crapola printer with a refurbished one. Or I can do plasma donations for 4 months and...
    Post by: SPyKER, Mar 29, 2017 in forum: Mods and Upgrades
  13. SPyKER
    Post

    Kickstarter Edition: Full rebuild help

    Not an option. Paying off debt to buy a house, and a replacement printer for one that is fixable for mostly the cost of my time is preferred. But...
    Post by: SPyKER, Mar 29, 2017 in forum: Mods and Upgrades
  14. SPyKER
    Post

    Kickstarter Edition: Full rebuild help

    I understand, Mark. Any "OG" that have any input other than Mark? I should be starting disassembly this evening.
    Post by: SPyKER, Mar 29, 2017 in forum: Mods and Upgrades
  15. SPyKER
    Thread

    Kickstarter Edition: Full rebuild help

    This thing has been a NIGHTMARE! I have never once gotten a working print out of this printer. I touted it all over the place when it was coming,...
    Thread by: SPyKER, Mar 27, 2017, 90 replies, in forum: Mods and Upgrades
Find older messages
Showing results 41 to 55 of 55
Search Again
Page 3 of 3