1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 2 of 3
  1. wickemu
    Post

    Solved Z-sensing component falls behind other Z pieces, causing bizarre layer height issues

    Restoring the firmware fixed it! Thanks.
    Post by: wickemu, Jul 6, 2017 in forum: Troubleshooting
  2. wickemu
    Post

    Solved Z-sensing component falls behind other Z pieces, causing bizarre layer height issues

    Right, so I'm assuming that the left side being separated leads to that. The question is how it could even get to that point, since due to the way...
    Post by: wickemu, Jul 6, 2017 in forum: Troubleshooting
  3. wickemu
    Post

    Solved Z-sensing component falls behind other Z pieces, causing bizarre layer height issues

    I'll give this a try once I can and update with the results. I'll also take a closer look at that right side - like I said, I see the wires, but...
    Post by: wickemu, Jul 6, 2017 in forum: Troubleshooting
  4. wickemu
    Post

    Solved Z-sensing component falls behind other Z pieces, causing bizarre layer height issues

    How would I do that? Sent from my iPhone using Tapatalk
    Post by: wickemu, Jul 6, 2017 in forum: Troubleshooting
  5. wickemu
    Post

    Solved Z-sensing component falls behind other Z pieces, causing bizarre layer height issues

    I don’t have it on hand right now so I won’t be able to take a closer look until later today, but based on a conversation you had with me in...
    Post by: wickemu, Jul 6, 2017 in forum: Troubleshooting
  6. wickemu
    Thread

    Solved Z-sensing component falls behind other Z pieces, causing bizarre layer height issues

    Pictures, because it's hard to grasp what I'm talking about without seeing it. Notice how it's normal at the bottom, then gets stretched further...
    Thread by: wickemu, Jul 6, 2017, 15 replies, in forum: Troubleshooting
  7. wickemu
    Post

    Solved Determining Robo 3D R1 version for fan shroud and/or "nozzle sock"?

    I'm happy to say that this has been resolved. Unexpectedly, a fan duct solved both problems: this shroud was easy to install with the stock fan...
    Post by: wickemu, Jul 5, 2017 in forum: General Questions
  8. wickemu
    Post

    Solved Determining Robo 3D R1 version for fan shroud and/or "nozzle sock"?

    Attached photo of the Z rod base. Considering that this printer has been used a dozen times at most, I'd be pretty surprised and annoyed if it...
    Post by: wickemu, Jun 19, 2017 in forum: General Questions
  9. wickemu
    Thread

    Solved Wobbling Along Y Axis

    Picture attached. The X and Z axes look great, but Y is inconsistent. What steps can I take to improve it? This printer came with a broken Y...
    Thread by: wickemu, Jun 19, 2017, 26 replies, in forum: Troubleshooting
  10. wickemu
    Thread

    Solved Determining Robo 3D R1 version for fan shroud and/or "nozzle sock"?

    I'm having an issue with my prints not being cooled quickly enough to set and my extruder cooling too quickly from the print fan. I'm therefore...
    Thread by: wickemu, Jun 19, 2017, 6 replies, in forum: General Questions
  11. wickemu
    Post

    Solved How do I reset autolevel memory?

    Ok, it looks like the solution was simply to remove the G29 command from my start gcode for the time being and just use G28. The bed's pretty...
    Post by: wickemu, Jun 17, 2017 in forum: Troubleshooting
  12. wickemu
    Post

    Solved How do I reset autolevel memory?

    Well the title of the post specifically mentioned a perceived autoleveling issue, so it seemed reasonable to assume that your directions were...
    Post by: wickemu, Jun 17, 2017 in forum: Troubleshooting
  13. wickemu
    Post

    Solved How do I reset autolevel memory?

    Ok, so I have been following the directions correctly - send M502, then send M500, Then send G28 and G29 to test... but that doesn't work. The...
    Post by: wickemu, Jun 17, 2017 in forum: Troubleshooting
  14. wickemu
    Post

    Solved How do I reset autolevel memory?

    Ok, though I could still use some clarification. Is this implying that the firmware needs to be reset by some separate means or that these...
    Post by: wickemu, Jun 17, 2017 in forum: Troubleshooting
  15. wickemu
    Post

    Solved How do I reset autolevel memory?

    So I'm supposed to do M500, then M501, then M502, then M500 again? I tried in both MatterControl and Repetier and it didn't work. I've attached...
    Post by: wickemu, Jun 17, 2017 in forum: Troubleshooting
  16. wickemu
    Thread

    Solved How do I reset autolevel memory?

    I made a dumb mistake with a recent print - right before it started the autolevel, I noticed a lot of filament gumming up on the nozzle. I...
    Thread by: wickemu, Jun 17, 2017, 16 replies, in forum: Troubleshooting
  17. wickemu
    Post

    Recommended first steps with an old stock Robo 3D?

    What do you use, and is it due to any specific advantage? I’m up for whatever works best and am not committed to any particular program. Sent...
    Post by: wickemu, Jun 16, 2017 in forum: General Questions
  18. wickemu
    Post

    Recommended first steps with an old stock Robo 3D?

    No LCD screen. I’m using the forked Cura but do have Matter Control installed as well. Sent from my iPhone using Tapatalk
    Post by: wickemu, Jun 16, 2017 in forum: General Questions
  19. wickemu
    Post

    Recommended first steps with an old stock Robo 3D?

    Interestingly enough, I found the culprit for the aborts to be the cooling fan overpowering the extruder heater. Once I changed it from the...
    Post by: wickemu, Jun 16, 2017 in forum: General Questions
  20. wickemu
    Post

    Recommended first steps with an old stock Robo 3D?

    Hm, all that is gibberish to me. Are you implying that I should go through with that Marlin installation or that I should wait for something else?...
    Post by: wickemu, Jun 16, 2017 in forum: General Questions
Showing results 21 to 40 of 41 Next >
Search Again
Page 2 of 3