1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 3 of 3
  1. wthierry
    Post

    Hmm.. printing slanted..

    Looks fine in the slicer. Used simplify 3d
    Post by: wthierry, Jul 25, 2017 in forum: Troubleshooting
  2. wthierry
    Thread

    Hmm.. printing slanted..

    Printed a 25mm calibration cube on the R2. Something not right, any thoughts??[ATTACH]
    Thread by: wthierry, Jul 24, 2017, 26 replies, in forum: Troubleshooting
  3. wthierry
    Post

    Heated bed cant get to 100 degrees?

    will do that. Thanks.
    Post by: wthierry, Jul 23, 2017 in forum: Troubleshooting
  4. wthierry
    Post

    Heated bed cant get to 100 degrees?

    Weird, I am only on my second print.....
    Post by: wthierry, Jul 23, 2017 in forum: Troubleshooting
  5. wthierry
    Thread

    Heated bed cant get to 100 degrees?

    Triied to set the bed to 100, seems it gets a communications error every time I try. Anyone else seen this?
    Thread by: wthierry, Jul 23, 2017, 9 replies, in forum: Troubleshooting
  6. wthierry
    Post

    First print pla

    Yea, going to lower it 5 degrees next time...
    Post by: wthierry, Jul 23, 2017 in forum: Show and Tell
  7. wthierry
    Post

    First print pla

    [ATTACH]
    Post by: wthierry, Jul 23, 2017 in forum: Show and Tell
  8. wthierry
    Thread

    First print pla

    Here is my first print after calibration in pla. Trying the same next in ABS, will post result.
    Thread by: wthierry, Jul 23, 2017, 4 replies, in forum: Show and Tell
  9. wthierry
    Post

    Filament run out detection

    Thanks for the pics. I am going to disable it. You didnt have to go through the trouble of opening it up, but thank you :)
    Post by: wthierry, Jul 18, 2017 in forum: Troubleshooting
  10. wthierry
    Thread

    Printer Bed adhesion ABS R2

    With the new printer bed in the R2, does anyone have to add anything to it when printing with ABS? or is it good to use as is?
    Thread by: wthierry, Jul 18, 2017, 1 replies, in forum: Troubleshooting
  11. wthierry
    Post

    Filament run out detection

    Well, I sent an email to support, will probably just disable it for now as suggested, and then take it apart when they send me a new sensor.
    Post by: wthierry, Jul 18, 2017 in forum: Troubleshooting
  12. wthierry
    Post

    Filament run out detection

    Is it worth taking it off and looking inside to check it our? Is it an easily replacable part? I have lots of replacment printer parts :)
    Post by: wthierry, Jul 18, 2017 in forum: Troubleshooting
  13. wthierry
    Post

    Filament run out detection

    I just started my first test print. I ended up with the message again, ran the wizard, and it keeps popping up. Where is the filament sensor on...
    Post by: wthierry, Jul 18, 2017 in forum: Troubleshooting
  14. wthierry
    Post

    Is the current wait time still 2 weeks?

    I bit the bullet and ordered one. Will wait and see...
    Post by: wthierry, Jun 11, 2017 in forum: Show and Tell
  15. wthierry
    Thread

    Is the current wait time still 2 weeks?

    In need of a new 3d printer. The R2 seems ideal, but I need to print some things by end of week. Anyone on here have any inside knowledge?...
    Thread by: wthierry, Jun 11, 2017, 5 replies, in forum: Show and Tell
  16. wthierry
    Profile Post

    alloy 910

    alloy 910
    Status update by wthierry, May 17, 2017
Find older messages
Showing results 41 to 56 of 56
Search Again
Page 3 of 3