1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 2 of 2
  1. Ed Neugebauer
    Post

    Unresolved No material extrusion during print

    Layer Height .2 MM Where do I find the layer width and Z offset in Matter Control?
    Post by: Ed Neugebauer, Jul 19, 2016 in forum: Troubleshooting
  2. Ed Neugebauer
    Post

    Unresolved No material extrusion during print

    Post by: Ed Neugebauer, Jul 19, 2016 in forum: Troubleshooting
  3. Ed Neugebauer
    Post

    Unresolved No material extrusion during print

    Well I thought I had it but it's still only printing only about 40% of the calibration ring. I don't understand why if I have it so close with the...
    Post by: Ed Neugebauer, Jul 19, 2016 in forum: Troubleshooting
  4. Ed Neugebauer
    Post

    Unresolved No material extrusion during print

    Thank you. I went through the procedure and made an adjustment but now I cannot move the Z-axis down far enough using MatterControl to touch the...
    Post by: Ed Neugebauer, Jul 19, 2016 in forum: Troubleshooting
  5. Ed Neugebauer
    Post

    Unresolved No material extrusion during print

    Okay I tried it again and now it will print the calibration circle but only half of it prints. Part of it prints too high too. My table is now...
    Post by: Ed Neugebauer, Jul 19, 2016 in forum: Troubleshooting
  6. Ed Neugebauer
    Post

    Unresolved No material extrusion during print

    It is still doing the exact same thing. I can manually extrude but it won't move the filament through when I print. I verified the new firmware...
    Post by: Ed Neugebauer, Jul 19, 2016 in forum: Troubleshooting
  7. Ed Neugebauer
    Post

    Unresolved No material extrusion during print

    I knew that and I remembered it after I made my previous post. My brain is like spaghetti right now after trying to figure this out for a few...
    Post by: Ed Neugebauer, Jul 19, 2016 in forum: Troubleshooting
  8. Ed Neugebauer
    Post

    Unresolved No material extrusion during print

    I see the plus firmware at the top of the page but will it work with the E3D V6?
    Post by: Ed Neugebauer, Jul 19, 2016 in forum: Troubleshooting
  9. Ed Neugebauer
    Post

    Unresolved No material extrusion during print

    I got it off of a link from the first page of the E3D V6 thread in this forum. My other E3D V6 clone starting doing the same thing even before I...
    Post by: Ed Neugebauer, Jul 19, 2016 in forum: Troubleshooting
  10. Ed Neugebauer
    Thread

    Unresolved No material extrusion during print

    My R1+ printer will extrude material no problem manually but when I go to print, it prints out very fine lines of material and then it stops...
    Thread by: Ed Neugebauer, Jul 19, 2016, 39 replies, in forum: Troubleshooting
  11. Ed Neugebauer
    Post

    E3D v6 Information, Installation Guides, and Review

    I got the real E3D v6 (direct from E3D in Great Britain with Bowden tube for $75.91 with overnight shipping to United States) and a Chinese one...
    Post by: Ed Neugebauer, Jul 10, 2016 in forum: Mods and Upgrades
  12. Ed Neugebauer
    Post

    Unresolved Bed Length Printer Area Shrinks

    Thank you for the help. I loosened both set screws and tried to move it up and down, but it would not move. I even left them loose to see if it...
    Post by: Ed Neugebauer, Apr 10, 2016 in forum: Troubleshooting
  13. Ed Neugebauer
    Post

    Unresolved Bed Length Printer Area Shrinks

    Okay as manually move the table backward the belt goes up the center capstan and down when I move it forward. How do I adjust the cog on the...
    Post by: Ed Neugebauer, Apr 10, 2016 in forum: Troubleshooting
  14. Ed Neugebauer
    Post

    Unresolved Bed Length Printer Area Shrinks

    I am using a skirt to prevent warpage, but I just want to know why the length is inconsistent. I do hear a crackling sound here and there as the...
    Post by: Ed Neugebauer, Apr 10, 2016 in forum: Troubleshooting
  15. Ed Neugebauer
    Thread

    Unresolved Bed Length Printer Area Shrinks

    I'm trying to print something this is 9.375 inches long and it's failed a few times because my print bed size on the length (y-axis) shrinks below...
    Thread by: Ed Neugebauer, Apr 10, 2016, 8 replies, in forum: Troubleshooting
Find older messages
Showing results 21 to 35 of 35
Search Again
Page 2 of 2