1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 2 of 10
  1. tkoco
    Post

    Christmas time

    Anyone wanting to see the R2 in action printing a Christmas bell: https://www.tiktok.com/t/ZTRmpq9Fr/
    Post by: tkoco, Oct 2, 2022 in forum: Show and Tell
  2. tkoco
    Post

    Sunlu Dehydrator update

    After investigating the different filament dryers, I settled on an EIBOS dryer...
    Post by: tkoco, Oct 2, 2022 in forum: Projects
  3. tkoco
    Thread

    Christmas time

    I have started with printing some Christmas themed bells. [ATTACH] Nice looking? Right? Check the next image when I add a light source within...
    Thread by: tkoco, Oct 1, 2022, 1 replies, in forum: Show and Tell
  4. tkoco
    Post

    Using an R2 to build a larger workhorse printer

    Does it growl when you don't feed it? (enough filament) It is a beast of a printer. :)
    Post by: tkoco, Oct 1, 2022 in forum: Show and Tell
  5. tkoco
    Post

    Red robo r2

    Nice job!
    Post by: tkoco, Oct 1, 2022 in forum: Show and Tell
  6. tkoco
    Post

    Raspberry Pi

    I would be interested in how you accomplished "Before replacing everything with Klipper....". Is the Klipper mod better than the original Robo OS?
    Post by: tkoco, Oct 1, 2022 in forum: General Questions
  7. tkoco
    Post

    Any admin present?

    As Mark says, experiment with small changes. Also, save each profile as a new profile with a new name before you make any changes. That way,...
    Post by: tkoco, Oct 1, 2022 in forum: General Questions
  8. tkoco
    Post

    What happens as the power supply brick fails

    Good information Lance. Thank you Sir.
    Post by: tkoco, Oct 1, 2022 in forum: General Questions
  9. tkoco
    Profile Post

    Busy printing stuff for the Holidays!

    Busy printing stuff for the Holidays!
    Status update by tkoco, Oct 1, 2022
  10. tkoco
    Post

    Hello,everyone!

    Ditto on the Welcome!
    Post by: tkoco, Oct 1, 2022 in forum: Introduction
  11. tkoco
    Post

    Removal of Upper support for Z axis rods

    Taking a stab at this: Looks like the black assembly needs to be separated from the white cover to expose the holding fastener.
    Post by: tkoco, Sep 27, 2022 in forum: Troubleshooting
  12. tkoco
    Post

    connection issue

    The listed 1.2.4 hex file has a bug in it. The listed 1.2.6 has the fix incorporated. I tested both of them on my R2.
    Post by: tkoco, Dec 22, 2020 in forum: Troubleshooting
  13. tkoco
    Post

    connection issue

    The last firmware version officially released is Marlin_1.1.6_RoboVersion_1.2.6_R2.hex
    Post by: tkoco, Dec 15, 2020 in forum: Troubleshooting
  14. tkoco
    Post

    connection issue

    As @Lance Weston suggest, try heating the bed manually from the touch panel. 40 C is ok ( warm enough to the touch without hurting you ) Try...
    Post by: tkoco, Dec 15, 2020 in forum: Troubleshooting
  15. tkoco
    Post

    connection issue

    The R2 FAQ has explicit instructions to help you determine your software and firmware levels. As far as Cura goes, I recommend that you upgrade to...
    Post by: tkoco, Dec 4, 2020 in forum: Troubleshooting
  16. tkoco
    Post

    connection issue

    What release of firmware and software are you using? ( http://community.robo3d.com/index.php?threads/r2-faq.23706/ )
    Post by: tkoco, Dec 2, 2020 in forum: Troubleshooting
  17. tkoco
    Post

    Good Build Plate I've Found for certain hard to print filaments

    Correct. Just don't use G36 coding. G28 followed by G29 works better if you wish to use auto-leveling.
    Post by: tkoco, Nov 25, 2020 in forum: Mods and Upgrades
  18. tkoco
    Post

    Good Build Plate I've Found for certain hard to print filaments

    As the print bed approaches a true level, you need to be careful with adjusting the corners. For glass plate surface, if the four corners are...
    Post by: tkoco, Nov 24, 2020 in forum: Mods and Upgrades
  19. tkoco
    Post

    Good Build Plate I've Found for certain hard to print filaments

    Have a look at this procedure: http://community.robo3d.com/index.php?threads/leveling-the-r2-print-bed.23492/
    Post by: tkoco, Nov 23, 2020 in forum: Mods and Upgrades
  20. tkoco
    Post

    Added a dual gear extruder with dual hotend capability

    Apologies Lance. I fail to see the " dual hotend capability" in the attached images.
    Post by: tkoco, Nov 13, 2020 in forum: Show and Tell
Showing results 21 to 40 of 192 Next >
Search Again
Page 2 of 10