1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 3 of 3
  1. Ocsff
    Post

    Solved Anyone ever seen this?

    That is correct you must print over the heated portion in order to assure good adhesion with those filaments
    Post by: Ocsff, Feb 29, 2016 in forum: Troubleshooting
  2. Ocsff
    Post

    Solved Anyone ever seen this?

    Glue stick will make it easier to remove parts from PEI as mentioned above
    Post by: Ocsff, Feb 29, 2016 in forum: Troubleshooting
  3. Ocsff
    Post

    Solved Anyone ever seen this?

    You have to use common sense and use the bed as it was intended. The outline on the bed shows approx area of heater on the underside. That is...
    Post by: Ocsff, Feb 29, 2016 in forum: Troubleshooting
  4. Ocsff
    Post

    Unanswered ROBO shuts down 2 hours in

    Pull the bottom off and check all your connections . Most common cause I have seen. Push the connections on even if they look ok.
    Post by: Ocsff, Feb 29, 2016 in forum: Troubleshooting
  5. Ocsff
    Post

    Unanswered xxl controller

    The controller is just an interface with the Ardueno which is the brains of the printer.
    Post by: Ocsff, Feb 29, 2016 in forum: Troubleshooting
  6. Ocsff
    Post

    Solved Anyone ever seen this?

    I have the solution to ever having another chip in your bed. I have 14 Robo3d printers and have had 3 chips from the bed. I replaced the bed and...
    Post by: Ocsff, Feb 29, 2016 in forum: Troubleshooting
  7. Ocsff
    Post

    Solved Printer unable to connect

    If your using matter control and disconnect the printer without first disconnecting in the program this can happen. Unplug your printer usb close...
    Post by: Ocsff, Feb 29, 2016 in forum: Troubleshooting
  8. Ocsff
    Post

    Unanswered xxl controller

    I assume z axis your referring to the z offset and its so low its rubbing on bed. If that is the case the XXL controller should not effect that....
    Post by: Ocsff, Feb 29, 2016 in forum: Troubleshooting
  9. Ocsff
    Post

    Unresolved How do I take off the nozzel?

    He has E3Dv6 Nozzle works same for Robo all metal nozzle that comes with the Robos
    Post by: Ocsff, Feb 26, 2016 in forum: Troubleshooting
  10. Ocsff
    Post

    Unresolved How do I take off the nozzel?

    Though you would look it up. Easy search with the info I gave you. Here is the link [MEDIA]
    Post by: Ocsff, Feb 26, 2016 in forum: Troubleshooting
  11. Ocsff
    Post

    Unresolved How do I take off the nozzel?

    you don't need to do any dis-assembly just heat up the nozzle and use two wrenches. Watch the Novice expert video I referred you to on you tube....
    Post by: Ocsff, Feb 26, 2016 in forum: Troubleshooting
  12. Ocsff
    Post

    Unresolved How do I take off the nozzel?

    refer to novice experts youtube video on nozzle removal. Has step by step
    Post by: Ocsff, Feb 25, 2016 in forum: Troubleshooting
Find older messages
Showing results 41 to 52 of 52
Search Again
Page 3 of 3