1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 3 of 6
  1. TstarkEngineering
    Post

    E3D Titan Extruder

    it might be. I just couldnt get it to work with the stock carriage nicely, but maybe your new carriage is better.
    Post by: TstarkEngineering, Apr 19, 2016 in forum: Mods and Upgrades
  2. TstarkEngineering
    Post

    E3D Titan Extruder

    With that design I'd like to see how your hotend fan mounts up. with the stock carriage being flat like that there was not enough room even with...
    Post by: TstarkEngineering, Apr 19, 2016 in forum: Mods and Upgrades
  3. TstarkEngineering
    Post

    E3D Titan Extruder

    as long as you are aware, i just hate for someone to finish only to find that out after the fact.
    Post by: TstarkEngineering, Apr 19, 2016 in forum: Mods and Upgrades
  4. TstarkEngineering
    Post

    E3D Titan Extruder

    @WheresWaldo Thank you, ya Im not going to waste my time trying to press them out I ordered new bearings. Thank you for the info! @everyone...
    Post by: TstarkEngineering, Apr 19, 2016 in forum: Mods and Upgrades
  5. TstarkEngineering
    Post

    E3D Titan Extruder

    Because looking at it at the front would offset it the opposite direction which would most likely cause problems with homing...
    Post by: TstarkEngineering, Apr 18, 2016 in forum: Mods and Upgrades
  6. TstarkEngineering
    Post

    E3D Titan Extruder

    well current job is at 41% probably wont install it tonight. Tomorrow possibly.
    Post by: TstarkEngineering, Apr 18, 2016 in forum: Mods and Upgrades
  7. TstarkEngineering
    Post

    E3D Titan Extruder

    Solidworks
    Post by: TstarkEngineering, Apr 18, 2016 in forum: Mods and Upgrades
  8. TstarkEngineering
    Post

    E3D Titan Extruder

    Sure is...:-) might have to alter it a little but it's v2.0 so there will probably be at least a 2.1 and 2.2
    Post by: TstarkEngineering, Apr 18, 2016 in forum: Mods and Upgrades
  9. TstarkEngineering
    Post

    E3D Titan Extruder

    I imagine it will work just fine. As far as I know some people are using them on their e3d Bigboxes. but its only 9 dollars. worst case you are...
    Post by: TstarkEngineering, Apr 18, 2016 in forum: Mods and Upgrades
  10. TstarkEngineering
    Post

    E3D Titan Extruder

    Im not home to tell if thats it, but Im pretty sure that is it. I havent had enough time to run tests so I am not sure if it will work with...
    Post by: TstarkEngineering, Apr 18, 2016 in forum: Mods and Upgrades
  11. TstarkEngineering
    Post

    E3D Titan Extruder

    no using the higher torque one...ill try and find the link...though it was purchased from stepperonline
    Post by: TstarkEngineering, Apr 18, 2016 in forum: Mods and Upgrades
  12. TstarkEngineering
    Post

    E3D Titan Extruder

    if its successful i will post STL file tomorrow
    Post by: TstarkEngineering, Apr 18, 2016 in forum: Mods and Upgrades
  13. TstarkEngineering
    Post

    E3D Titan Extruder

    [IMG]
    Post by: TstarkEngineering, Apr 18, 2016 in forum: Mods and Upgrades
  14. TstarkEngineering
    Post

    E3D Titan Extruder

    nope going with a new carriage... I cant see any way of it working with the stock carriage a nice way.
    Post by: TstarkEngineering, Apr 18, 2016 in forum: Mods and Upgrades
  15. TstarkEngineering
    Post

    E3D Titan Extruder

    My new design is actually about .010" less than the original design in the x direction. Which means no loss of x. It also means possible z height...
    Post by: TstarkEngineering, Apr 18, 2016 in forum: Mods and Upgrades
  16. TstarkEngineering
    Post

    E3D Titan Extruder

    There are probably ways around it but cheesy ways...I want something that looks nice, functions properly and isnt hacked together... round 2 here...
    Post by: TstarkEngineering, Apr 18, 2016 in forum: Mods and Upgrades
  17. TstarkEngineering
    Post

    E3D Titan Extruder

    I think the only way to truly get it to work right is an entire new carriage design...Im still not happy with mine..
    Post by: TstarkEngineering, Apr 18, 2016 in forum: Mods and Upgrades
  18. TstarkEngineering
    Post

    E3D Titan Extruder

    Yes it does that's why it was designed that way as well. Its at the lowest point it can go on top of the main carriage. Raising the V6 further up...
    Post by: TstarkEngineering, Apr 17, 2016 in forum: Mods and Upgrades
  19. TstarkEngineering
    Post

    E3D Titan Extruder

    Are you just using 1 hold down?
    Post by: TstarkEngineering, Apr 17, 2016 in forum: Mods and Upgrades
  20. TstarkEngineering
    Post

    E3D Titan Extruder

    In order to use the stock carriage with stock mounting points this was the only solution that I could see at the time. My goal was to design a...
    Post by: TstarkEngineering, Apr 17, 2016 in forum: Mods and Upgrades
Showing results 41 to 60 of 114 Next >
Search Again
Page 3 of 6