1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 2 of 2
  1. PropLord
    Post

    Answered Strange rescaling during print?

    How might I go about doing that? That's what I was asking about earlier.
    Post by: PropLord, Mar 6, 2017 in forum: Troubleshooting
  2. PropLord
    Post

    Answered Strange rescaling during print?

    While I'm looking for a mouse size screwdriver, I printed a cube. When it was done, it was: (X) 12/16" (Y) 12/16" (Z) 10.5~/16" Just like the...
    Post by: PropLord, Mar 6, 2017 in forum: Troubleshooting
  3. PropLord
    Post

    Answered Strange rescaling during print?

    I must be missing something. I opened up the machine and I don't see anything resembling a card. How do I change the stepper driver card?
    Post by: PropLord, Mar 6, 2017 in forum: Troubleshooting
  4. PropLord
    Post

    Answered Strange rescaling during print?

    It's a threaded rod with a coupler believe. I attached some pictures (and a picture of the model number, 0340). There about 21 threads per inch....
    Post by: PropLord, Mar 6, 2017 in forum: Troubleshooting
  5. PropLord
    Post

    Answered Strange rescaling during print?

    I just stumbled upon someone else having the same problem. And they fixed it by doing something with the Firmware. The link that someone else...
    Post by: PropLord, Mar 6, 2017 in forum: Troubleshooting
  6. PropLord
    Post

    Answered Strange rescaling during print?

    The extra density did nothing but waste more filament. When I print it as a full piece it prints just fine. "Basically" a circle. But I have to...
    Post by: PropLord, Mar 6, 2017 in forum: Troubleshooting
  7. PropLord
    Post

    Answered Strange rescaling during print?

    Your test model seems to have come out perfect. Now, one detail I forgot to mention was I printed the Thor chest Disk models at 10% infill. Could...
    Post by: PropLord, Mar 5, 2017 in forum: Troubleshooting
  8. PropLord
    Post

    Answered Strange rescaling during print?

    I cut them in half, and made them sit flat, like in the pictures. If there was something wrong with the X or Y axis, there should be gapes where...
    Post by: PropLord, Mar 5, 2017 in forum: Troubleshooting
  9. PropLord
    Thread

    Answered Strange rescaling during print?

    I'm working on the disks on Thor's costume for my cousin. The model is great, good topology, high-poly with a file size of about 2mb. Great. But...
    Thread by: PropLord, Mar 4, 2017, 31 replies, in forum: Troubleshooting
  10. PropLord
    Post

    Solved Y-Axis slipping

    I know it's been a while since I last posted. It was indeed the Y-Belt. I tightened it by 1 tooth and I haven't had a problem since. I've had...
    Post by: PropLord, Sep 5, 2016 in forum: Troubleshooting
  11. PropLord
    Post

    Solved Y-Axis slipping

    I'll try that out too. What causes the entire job to shift though? I'm sure you know WAAAY more than I do, so I'm not questioning your knowledge...
    Post by: PropLord, Jun 22, 2016 in forum: Troubleshooting
  12. PropLord
    Post

    Solved Y-Axis slipping

    I'll check the screws. I also tightened the belt by 1 tooth. It's definitely moving forwards and backwards. It doesn't have too hard of a time...
    Post by: PropLord, Jun 22, 2016 in forum: Troubleshooting
  13. PropLord
    Thread

    Solved Y-Axis slipping

    I'm new to the 3d printing world and I got my Robo 3d Refurbished model a couple of weeks ago. I'd like to say it's been great, but I had a lot...
    Thread by: PropLord, Jun 21, 2016, 10 replies, in forum: Troubleshooting
Find older messages
Showing results 21 to 33 of 33
Search Again
Page 2 of 2