1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 2 of 2
  1. TRAVIS KEMP
    Post

    Marlin Firmware Upgrade 1.1.0 RC8 & RCBugFix (For R1 & R1+PLUS)

    :Printer halted. kill() called! this is what i am getting, only when it is plugged into the ramps board, im getting that on s3d, and when looking...
    Post by: TRAVIS KEMP, Nov 18, 2016 in forum: Mods and Upgrades
  2. TRAVIS KEMP
    Post

    Marlin Firmware Upgrade 1.1.0 RC8 & RCBugFix (For R1 & R1+PLUS)

    i converted my company logo to a dec layout, got the numbers, placed it in the startbmp location and thats it, thats the only thing i have done,...
    Post by: TRAVIS KEMP, Nov 18, 2016 in forum: Mods and Upgrades
  3. TRAVIS KEMP
    Post

    Marlin Firmware Upgrade 1.1.0 RC8 & RCBugFix (For R1 & R1+PLUS)

    so i got it to compile, but i plugged in the controller and the backlight just lights up, not text or images or anything?
    Post by: TRAVIS KEMP, Nov 18, 2016 in forum: Mods and Upgrades
  4. TRAVIS KEMP
    Post

    Marlin Firmware Upgrade 1.1.0 RC8 & RCBugFix (For R1 & R1+PLUS)

    need some quick help. got a graphic lcd today, i had originally disabled the lcd on marlin rc7(because i didnt have one then) but now its saying...
    Post by: TRAVIS KEMP, Nov 18, 2016 in forum: Mods and Upgrades
  5. TRAVIS KEMP
    Post

    Marlin Firmware Upgrade 1.1.0 RC8 & RCBugFix (For R1 & R1+PLUS)

    I also have two high cfm 40mm fans blowing on the board from the from of the case, with holes cut in the front, and some vent holes drilled all...
    Post by: TRAVIS KEMP, Nov 16, 2016 in forum: Mods and Upgrades
  6. TRAVIS KEMP
    Post

    Marlin Firmware Upgrade 1.1.0 RC8 & RCBugFix (For R1 & R1+PLUS)

    Awesome, thanks for the fast response! Very much appreciated! I'l probably just order a full graphics. Also, I'm currently running the PSU at...
    Post by: TRAVIS KEMP, Nov 16, 2016 in forum: Mods and Upgrades
  7. TRAVIS KEMP
    Post

    Marlin Firmware Upgrade 1.1.0 RC8 & RCBugFix (For R1 & R1+PLUS)

    Morning! So i finally did the rc7, and am loving the mesh leveling and its just far better than the original firmware, so thanks waldo, and...
    Post by: TRAVIS KEMP, Nov 16, 2016 in forum: Mods and Upgrades
  8. TRAVIS KEMP
    Post

    Marlin Firmware Upgrade 1.1.0 RC8 & RCBugFix (For R1 & R1+PLUS)

    So here are results of before and after making the stops hit equally(since my OP I did make small adjustments the the stops, tightening etc.) Let...
    Post by: TRAVIS KEMP, Apr 13, 2016 in forum: Mods and Upgrades
  9. TRAVIS KEMP
    Post

    Marlin Firmware Upgrade 1.1.0 RC8 & RCBugFix (For R1 & R1+PLUS)

    Ok, got ya, my config was stated as true, unless I'm understanding this backward (because I do a lot of end use prints and precision is key) i...
    Post by: TRAVIS KEMP, Apr 13, 2016 in forum: Mods and Upgrades
  10. TRAVIS KEMP
    Post

    Marlin Firmware Upgrade 1.1.0 RC8 & RCBugFix (For R1 & R1+PLUS)

    Ok, thank you very much, I'm ok with mechanically leveling. I'm just not sure of the best way to go about it. I did the search but it only...
    Post by: TRAVIS KEMP, Apr 13, 2016 in forum: Mods and Upgrades
  11. TRAVIS KEMP
    Post

    Marlin Firmware Upgrade 1.1.0 RC8 & RCBugFix (For R1 & R1+PLUS)

    Thank you for your quick response and insight. I do understand the risks, and other than being un-level and not auto compensating this printer...
    Post by: TRAVIS KEMP, Apr 13, 2016 in forum: Mods and Upgrades
  12. TRAVIS KEMP
    Post

    Marlin Firmware Upgrade 1.1.0 RC8 & RCBugFix (For R1 & R1+PLUS)

    Hello, New here posting wise but have been following for a little while. I have a question/favor. I am running S3D on an R1 plus. Up until a...
    Post by: TRAVIS KEMP, Apr 13, 2016 in forum: Mods and Upgrades
Find older messages
Showing results 21 to 32 of 32
Search Again
Page 2 of 2