1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 1 of 2
  1. Schlomo
    Post

    Marlin Firmware Upgrade 1.1.0 RC8 & RCBugFix (For R1 & R1+PLUS)

    I see. I had to check the Shoutbox to get context on what you meant by "G29 P6 is the wrong way to do it" but i see what you mean now. Let me...
    Post by: Schlomo, Mar 22, 2017 in forum: Mods and Upgrades
  2. Schlomo
    Post

    Marlin Firmware Upgrade 1.1.0 RC8 & RCBugFix (For R1 & R1+PLUS)

    Yep
    Post by: Schlomo, Mar 22, 2017 in forum: Mods and Upgrades
  3. Schlomo
    Post

    Marlin Firmware Upgrade 1.1.0 RC8 & RCBugFix (For R1 & R1+PLUS)

    I was able to get this working yesterday as well. I was anxiously following your updates, Waldo, but decided to dive into it myself most likely...
    Post by: Schlomo, Mar 22, 2017 in forum: Mods and Upgrades
  4. Schlomo
    Post

    Schlomo's Robo Beast Inspired Printer!

    All I have is a single fan with no shroud. Works pretty well. In S3D i up the cooling for bridging from 50% to 100%, but other than than just...
    Post by: Schlomo, Mar 16, 2016 in forum: Show and Tell
  5. Schlomo
    Post

    Solved Bubbling on bed, where do I start?

    That looks more like bubbles under the surface of your contact paper or whatever you're putting down on your bed. Is it absolutely smooth? Just...
    Post by: Schlomo, Mar 15, 2016 in forum: Troubleshooting
  6. Schlomo
    Thread

    Schlomo's Robo Beast Inspired Printer!

    First things first, credit where credit is due. Thank you to dbefore for posting up his instructions for this build as well as STL's. No way I...
    Thread by: Schlomo, Mar 10, 2016, 4 replies, in forum: Show and Tell
  7. Schlomo
    Post

    Partial Answer This Is Not a Circle: Unable to Print Anything

    That sounds more to me like a loose y belt... Could you lift the glass bed off the y axis carriage (held on by 4 magnets) and check the belt to...
    Post by: Schlomo, Mar 2, 2016 in forum: Troubleshooting
  8. Schlomo
    Post

    PC eSUN ePC filament

    Yeah, i had to lower my speed with all filaments due to my extruder grinding badly, waiting on a new MK7 gear to try out but for now its slower...
    Post by: Schlomo, Feb 18, 2016 in forum: Printing Filament
  9. Schlomo
    Post

    PC eSUN ePC filament

    [IMG] [IMG] Printed at: 250°C Extrusion 110°C Bed 35mm/s speed 0.200 layer height 2 perimeters 40% Honeycomb Fast 3bottom layers, 3 top layers...
    Post by: Schlomo, Feb 18, 2016 in forum: Printing Filament
  10. Schlomo
    Post

    PC eSUN ePC filament

    Looks good. I didnt get any warping with PEI at 110c bed temp.
    Post by: Schlomo, Feb 18, 2016 in forum: Printing Filament
  11. Schlomo
    Post

    RAMPS 1.3 vs RAMPS 1.4 in Marlin

    Just making sure. I can confirm the default source defines Ramps 1.3 as the board, not 1.4
    Post by: Schlomo, Feb 17, 2016 in forum: General Questions
  12. Schlomo
    Post

    RAMPS 1.3 vs RAMPS 1.4 in Marlin

    I meant my Firmware had specified my board to be RAMPS 1.3, not that I was using a 1.3 physical board.
    Post by: Schlomo, Feb 17, 2016 in forum: General Questions
  13. Schlomo
    Post

    Unresolved Wierd Problem

    What is your first layer height? Extrude the first layer and stop your print and check. It should be close to what you set in your slicer.. Do...
    Post by: Schlomo, Feb 16, 2016 in forum: Troubleshooting
  14. Schlomo
    Post

    RAMPS 1.3 vs RAMPS 1.4 in Marlin

    Awesome thanks, good to know.
    Post by: Schlomo, Feb 13, 2016 in forum: General Questions
  15. Schlomo
    Thread

    RAMPS 1.3 vs RAMPS 1.4 in Marlin

    Hi, Does anyone know the difference between ramps 1.3 vs 1.4 in Marlin firmware? I just realized i've been using 1.3 for my Robo 3D r1 +Plus...
    Thread by: Schlomo, Feb 12, 2016, 10 replies, in forum: General Questions
  16. Schlomo
    Post

    PC eSUN ePC filament

    I successfully used the ePC material yesterday. I have an actively heated chamber which gets up to 70c so i needed to replace my x carriage which...
    Post by: Schlomo, Feb 8, 2016 in forum: Printing Filament
  17. Schlomo
    Post

    PEI Print Bed

    Yeah, you basically hit the nail on the head with the problems I was having. I was able to solve most of them and am getting good larger prints...
    Post by: Schlomo, Feb 7, 2016 in forum: Mods and Upgrades
  18. Schlomo
    Post

    PEI Print Bed

    I got it working reasonably well for smaller parts, but this stuff leant really make sense to me. I had to lower my initial layer heist down to...
    Post by: Schlomo, Feb 6, 2016 in forum: Mods and Upgrades
  19. Schlomo
    Post

    R1+ Auto-Level not really accurate

    So. I got mine dialed in. Turns out, the front 2 magnets were placed from the factory too far apart. So, even if i shimmed something up, by...
    Post by: Schlomo, Feb 3, 2016 in forum: General Questions
  20. Schlomo
    Post

    R1+ Auto-Level not really accurate

    Well, im glad im not the only one. Good to know there are inherent issues with the bed leveling routine, as I put too much trust in the G29, i...
    Post by: Schlomo, Feb 3, 2016 in forum: General Questions
Showing results 1 to 20 of 27 Next >
Search Again
Page 1 of 2