1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 1 of 2
  1. LumpyDVC
    Post

    New Calgary Robo R1 Owner

    I've been using this method since I got my printer in December. Tried hairspray but it was messy. Ya with glue stick you have to clean even 3-4...
    Post by: LumpyDVC, May 16, 2016 in forum: Canada
  2. LumpyDVC
    Post

    New Calgary Robo R1 Owner

    I use glue stick and run my bed at 68 for PLA. Works great. Sent from my SM-G900W8 using Tapatalk
    Post by: LumpyDVC, May 16, 2016 in forum: Canada
  3. LumpyDVC
    Post

    New Calgary Robo R1 Owner

    I used this mod. You do need to change a piece under/around the hotend but it's not that difficult. http://www.thingiverse.com/thing:821080
    Post by: LumpyDVC, May 15, 2016 in forum: Canada
  4. LumpyDVC
    Post

    New Calgary Robo R1 Owner

    A few people have had top mounted spools fail and crash down on their heat beds. Me, I had one of my dogs get tangled on a cable and dragged my...
    Post by: LumpyDVC, May 6, 2016 in forum: Canada
  5. LumpyDVC
    Post

    New Calgary Robo R1 Owner

    Upgrades I would recommend Feet Filament quick change Wire chain Look for spool holders that are not mounted above Robo. New heat beds are...
    Post by: LumpyDVC, May 5, 2016 in forum: Canada
  6. LumpyDVC
    Post

    New Calgary Robo R1 Owner

    Welcome Karl! You will enjoy your printer. I'm in Red Deer
    Post by: LumpyDVC, May 4, 2016 in forum: Canada
  7. LumpyDVC
    Post

    What gcode do i use to get bed to move towards me after print finishes?

    Use - Replace the 245 with whatever works best for your beds Y dimension. G1 Y245 I have this added to my end script in Simplify3D.
    Post by: LumpyDVC, Apr 15, 2016 in forum: General Questions
  8. LumpyDVC
    Thread

    Simplify3D / Octoprint - GCode Direct to Octoprint Setup

    Hey All, Found this nifty workaround on the Simplify3D forums for automating the sending of GCode directly to your Octoprint setup. No more...
    Thread by: LumpyDVC, Apr 5, 2016, 20 replies, in forum: Software
  9. LumpyDVC
    Post

    Ribbon Cable Clamp for Robo 3D R1 Plus

    Printed. Works great! P.S. I would be interested in a cable chain for the bed heater cable.
    Post by: LumpyDVC, Mar 31, 2016 in forum: Mods and Upgrades
  10. LumpyDVC
    Post

    Overnight Prints - Tips?

    It was my first venture with a Raspberry Pi. It's actually very easy to do. Here is the YouTube video I used for my OctoPrint setup. [MEDIA]
    Post by: LumpyDVC, Mar 10, 2016 in forum: General Questions
  11. LumpyDVC
    Post

    Solved Humming Noise When Powering On

    The power supply fan in there is a 60mmx60mm and can be replaced like the others. I suggest using rubber pull-through fan mounts to help deaden...
    Post by: LumpyDVC, Mar 10, 2016 in forum: Troubleshooting
  12. LumpyDVC
    Post

    Overnight Prints - Tips?

    I use OctoPrint, so I check my long prints during the night from my cell phone. Got another 22hr print going right now. #2 of 3 on the go.
    Post by: LumpyDVC, Mar 10, 2016 in forum: General Questions
  13. LumpyDVC
    Post

    Overnight Prints - Tips?

    Some no brainers.... - Make sure you have more than adequate filament for the print and a good spool setup (no resistance/sturdy) - Print from SD...
    Post by: LumpyDVC, Mar 10, 2016 in forum: General Questions
  14. LumpyDVC
    Post

    Unanswered Quieter fans for the R1

    You can fit a 60mm x 25mm fan in the PSU. I just did this yesterday. Also used rubber fan mounts rather than screwing it tight to the lid. That...
    Post by: LumpyDVC, Mar 10, 2016 in forum: General Questions
  15. LumpyDVC
    Post

    Unresolved Robo R1+ prints not centering on y axis as shown in Mattercontrol

    Lael, Have you recently done anything with your Robo firmware? I did some tweaks to the firmware Robo Tech sent me. Ever since I did that my...
    Post by: LumpyDVC, Feb 16, 2016 in forum: Troubleshooting
  16. LumpyDVC
    Post

    Answered Basic questions for after printing (1st print)

    Here ya go. Quick Change - http://www.thingiverse.com/thing:889541 Deck Hole Cover - (For use with Wire Chain) -...
    Post by: LumpyDVC, Feb 16, 2016 in forum: Troubleshooting
  17. LumpyDVC
    Post

    Answered Basic questions for after printing (1st print)

    Hey Kris with a K, I find it easier on larger prints to let them cool down before attempting to remove. Little prints I'll normally give them a...
    Post by: LumpyDVC, Feb 16, 2016 in forum: Troubleshooting
  18. LumpyDVC
    Post

    Solved Buying (or printing?) a replacement for the piece that holds the filament against the hobbed bolt

    Filament Tensioner. Glue it back together and print a replacement or better yet print and replace with the Quick-Change Filament mod from...
    Post by: LumpyDVC, Feb 16, 2016 in forum: Troubleshooting
  19. LumpyDVC
    Post

    PLA Filaments.ca Has another used it....

    I just got an order in from spool3d. Product seems decent. Could do without the additional $3 in packaging. They were out of black when I ordered...
    Post by: LumpyDVC, Feb 13, 2016 in forum: Printing Filament
  20. LumpyDVC
    Post

    Solved Bed traveling to far for last 3 points during autolevel process.

    Double check your bed size is entered correctly in your slicer software.
    Post by: LumpyDVC, Feb 7, 2016 in forum: Troubleshooting
Showing results 1 to 20 of 21 Next >
Search Again
Page 1 of 2