1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 1 of 2
  1. afat08
    Post

    Solved Bottom layer coming weird?

    Infill overlap possibly?
    Post by: afat08, Feb 25, 2016 in forum: Troubleshooting
  2. afat08
    Post

    Unresolved Busted a part. :(

    This seems like something I should print just to have on hand, even if under warranty, it would get me through until Robo can replace it...?
    Post by: afat08, Feb 25, 2016 in forum: Troubleshooting
  3. afat08
    Post

    Unresolved Wierd Problem

    I have noticed recently that this problem is mainly cause when printing overhangs or when trying to go up and out at the same time...
    Post by: afat08, Feb 25, 2016 in forum: Troubleshooting
  4. afat08
    Post

    NinjaFlex filament

    [MEDIA] Pretty good video showing the settings for printing with the ninjaflex
    Post by: afat08, Feb 16, 2016 in forum: Printing Filament
  5. afat08
    Post

    Unresolved Wierd Problem

    BUMP...Just picked up my digital calipers and ran a 20mm test cube. It came out almost dead accurate within +/- .03 mm tolerance. And the extruder...
    Post by: afat08, Feb 16, 2016 in forum: Troubleshooting
  6. afat08
    Post

    Unanswered Help with Cura Settings

    When I did mine, I sat there running first layer after first layer and cleaning the bed each and every time until I finally had it fine tuned....
    Post by: afat08, Feb 12, 2016 in forum: Troubleshooting
  7. afat08
    Post

    Unresolved Bed Not Returning to 0 degrees when printing with SD card

    If your bed remains at the same print temp then you have a problem, but if it simply is just not going to 0, it probably won't unless your room...
    Post by: afat08, Feb 12, 2016 in forum: Troubleshooting
  8. afat08
    Post

    Unresolved Cure: no supports being printed?

    Layout looks different from mine, but the support settings appear to be the same and I have no problems with printing supports so this is beyond...
    Post by: afat08, Feb 8, 2016 in forum: Troubleshooting
  9. afat08
    Post

    Unresolved Cure: no supports being printed?

    What do you have your "Expert Config" set at (the three "..." button next to it)?
    Post by: afat08, Feb 5, 2016 in forum: Troubleshooting
  10. afat08
    Post

    Unresolved Issues with vertical circles

    [ATTACH]
    Post by: afat08, Feb 3, 2016 in forum: Troubleshooting
  11. afat08
    Post

    Unresolved Nozzel rubs plastic as it travels causing strings.

    Give Cura a shot. I've only used MC and Cura, so I can't comment on the rest, but I definitely prefer Cura and havn't had a problem with it yet...
    Post by: afat08, Feb 2, 2016 in forum: Troubleshooting
  12. afat08
    Post

    E3D v6 Information, Installation Guides, and Review

    I got mine from them and it came with everything, small piece of tubing as well
    Post by: afat08, Feb 2, 2016 in forum: Mods and Upgrades
  13. afat08
    Post

    Solved extruder clog on r1 plus+, can't remove hot end

    I just went through this with mine, because all the information I find is for the older version. What I found when taking mine apart is that the...
    Post by: afat08, Feb 2, 2016 in forum: Troubleshooting
  14. afat08
    Post

    Unresolved Wierd Problem

    Sorry, I was very busy over the weekend and could not get a good pic or video to show what is happening. I will try today or tomorrow...Just by...
    Post by: afat08, Feb 1, 2016 in forum: Troubleshooting
  15. afat08
    Post

    Solved Extruder heating up, then cooling back down when it starts to print.

    Drop the bed temp down to 70 and try that
    Post by: afat08, Jan 31, 2016 in forum: Troubleshooting
  16. afat08
    Post

    Answered Wire harness issue

    Any pictures?
    Post by: afat08, Jan 30, 2016 in forum: Troubleshooting
  17. afat08
    Post

    Solved Extruder heating up, then cooling back down when it starts to print.

    Are you running a heated bed? If so, what temp?
    Post by: afat08, Jan 30, 2016 in forum: Troubleshooting
  18. afat08
    Post

    Solved Setting Z-axis offset

    What slicer are you using to generate the G-Code? It took me first layer after first layer of trial and error to fine tune my first layer and...
    Post by: afat08, Jan 30, 2016 in forum: Troubleshooting
  19. afat08
    Post

    Unresolved Wierd Problem

    Ya I guess I should put my info in my sig so you all know...but I have the r1+ just purchased from BB a few weeks ago. Just the stock firmware...
    Post by: afat08, Jan 28, 2016 in forum: Troubleshooting
  20. afat08
    Post

    Unresolved Wierd Problem

    After running the calibration test, I found that it wasn't that far off but could use some tweaking. But the thing is, it was the opposite of what...
    Post by: afat08, Jan 28, 2016 in forum: Troubleshooting
Showing results 1 to 20 of 24 Next >
Search Again
Page 1 of 2