1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
  1. Demoux
    Post

    Solved Extruder heating up, then cooling back down when it starts to print.

    I would upgrade it, but it isn't my printer. I will more than likely buy my own at some point and do all of these things before I really start...
    Post by: Demoux, Feb 2, 2016 in forum: Troubleshooting
  2. Demoux
    Post

    Solved Extruder heating up, then cooling back down when it starts to print.

    They sure are. If I have any solder left back at home I will do a quick fix, but I will still order some new ones. Them being as fragile as they...
    Post by: Demoux, Feb 2, 2016 in forum: Troubleshooting
  3. Demoux
    Post

    Solved Extruder heating up, then cooling back down when it starts to print.

    Much thanks. I'll order a few tonight. Let me change the thread to resolved. Thanks for everyones help. Glad to pinpoint the problem for sure.
    Post by: Demoux, Feb 2, 2016 in forum: Troubleshooting
  4. Demoux
    Post

    Solved Extruder heating up, then cooling back down when it starts to print.

    It was the thermistor. I noticed the black cover was kind of hard to pull back over the red wire, so I pulled it back a bit and somehow the red...
    Post by: Demoux, Feb 2, 2016 in forum: Troubleshooting
  5. Demoux
    Post

    Solved Extruder heating up, then cooling back down when it starts to print.

    The thermistor is reading fine. When I tell it to preheat, the temperature slowly climbs like it usually does. When it gets that error after...
    Post by: Demoux, Feb 1, 2016 in forum: Troubleshooting
  6. Demoux
    Post

    Solved Extruder heating up, then cooling back down when it starts to print.

    Well the problem isn't so much with the bed. When I start the print the bed heats fine. The bed isn't the problem, its the extruder. It heats fine...
    Post by: Demoux, Feb 1, 2016 in forum: Troubleshooting
  7. Demoux
    Post

    Solved Extruder heating up, then cooling back down when it starts to print.

    G28 ; home all axes G29 G1 Z5 F5000 ; lift nozzle M109 S[temperature] ; set the extruder temp and wait G28 Z0 ; Home Z again in case there was...
    Post by: Demoux, Feb 1, 2016 in forum: Troubleshooting
  8. Demoux
    Post

    Solved Extruder heating up, then cooling back down when it starts to print.

    Here's a log. I turned the printer on, connected, and preheated. A noteable error that I am getting on the console is <-Error:Extruder switched...
    Post by: Demoux, Feb 1, 2016 in forum: Troubleshooting
  9. Demoux
    Post

    Solved Extruder heating up, then cooling back down when it starts to print.

    Done. The bed preheats fine. it stops heating if I start to preheat the extruder, however.
    Post by: Demoux, Feb 1, 2016 in forum: Troubleshooting
  10. Demoux
    Post

    Solved Extruder heating up, then cooling back down when it starts to print.

    I can check the console log tomorrow. As I said, it is a school printer. I will post a log if possible. I am running a heated bed. It runs at...
    Post by: Demoux, Jan 31, 2016 in forum: Troubleshooting
  11. Demoux
    Thread

    Solved Extruder heating up, then cooling back down when it starts to print.

    Before I start, this printer is a school printer owned by my computers teacher. I unboxed it, set it up and got it running, and have been...
    Thread by: Demoux, Jan 29, 2016, 33 replies, in forum: Troubleshooting
Showing results 1 to 11 of 11
Search Again