1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 1 of 3
  1. cdsl810
    Post

    Simplify 3d

    Make sure that in the G-Code tab your Z offset is set correctly too. If your starting too high, the filament won't stick and the first layer will...
    Post by: cdsl810, Mar 14, 2016 in forum: Software
  2. cdsl810
    Post

    Marlin Firmware Upgrade 1.1.0 RC8 & RCBugFix (For R1 & R1+PLUS)

    I didn't need to upgrade the firmware until I began modifying the printer. If your ROBO is stock, don't touch the firmware.
    Post by: cdsl810, Mar 13, 2016 in forum: Mods and Upgrades
  3. cdsl810
    Post

    Marlin Firmware Upgrade 1.1.0 RC8 & RCBugFix (For R1 & R1+PLUS)

    Looking forward to it! The novelty of ABL has worn off for me. Mesh leveling will only improve the quality of the great prints that have been...
    Post by: cdsl810, Mar 10, 2016 in forum: Mods and Upgrades
  4. cdsl810
    Post

    E3D v6 Information, Installation Guides, and Review

    You will need to print a new part to allow the E3D to fit properly. It is a thicker quick release plate: http://www.thingiverse.com/thing:1192896...
    Post by: cdsl810, Mar 10, 2016 in forum: Mods and Upgrades
  5. cdsl810
    Post

    E3D v6 Information, Installation Guides, and Review

    Because the E3D v6 uses a PTFE tube that runs from the hobbed bolt down to the heat break, I would say most definitely it will help with softer...
    Post by: cdsl810, Mar 9, 2016 in forum: Mods and Upgrades
  6. cdsl810
    Post

    Solved Temp Fall Error

    There is also a chance that you have a bad heater or funky thermistor.
    Post by: cdsl810, Mar 8, 2016 in forum: Troubleshooting
  7. cdsl810
    Post

    Solved Temp Fall Error

    I don't think the error is caused by your Cura settings at all. Check to make sure the thermistor and heater connections are good, and then make...
    Post by: cdsl810, Mar 8, 2016 in forum: Troubleshooting
  8. cdsl810
    Post

    What is the easiest software to make stl/modeling

    Onshape is free, TinkerCAD is free... they both work well, but are cloud-based only. I think Onshape is a tad easier to learn and use.
    Post by: cdsl810, Mar 4, 2016 in forum: Software
  9. cdsl810
    Post

    MatterControl 1.5 not auto level

    Did you ADD PRINTER again when you installed 1.5? If you upgraded directly from 1.4 it will save your settings... but if you uninstalled 1.4 and...
    Post by: cdsl810, Mar 4, 2016 in forum: Troubleshooting
  10. cdsl810
    Post

    Solved Thermal Runaway

    Gotcha. You have already helped me and many others a great deal with our ROBO setups. I greatly appreciate your prompt and wise responses. I will...
    Post by: cdsl810, Mar 3, 2016 in forum: Troubleshooting
  11. cdsl810
    Post

    Solved Thermal Runaway

    Well, with the Configuration_adv.h values copied directly from the RC3... I had success. The temp did drop in that portion of the print, but the...
    Post by: cdsl810, Mar 3, 2016 in forum: Troubleshooting
  12. cdsl810
    Post

    Solved Thermal Runaway

    After re-tuning the PID with the fan on, the print failed with a THERMAL RUNAWAY error in exactly the same spot as the previous 2 failed prints....
    Post by: cdsl810, Mar 2, 2016 in forum: Troubleshooting
  13. cdsl810
    Post

    Solved Thermal Runaway

    I updated the PID values in the firmware and then uploaded. I am trying the autotune once more right now with the parts fan on full speed. I will...
    Post by: cdsl810, Mar 2, 2016 in forum: Troubleshooting
  14. cdsl810
    Post

    Solved Thermal Runaway

    OK. I guess that wasn't it. There are no loose connections for sure--everything is soldered and there are no connectors between the...
    Post by: cdsl810, Mar 2, 2016 in forum: Troubleshooting
  15. cdsl810
    Post

    Solved Thermal Runaway

    It turns out that overcooling was the cause. It only happens very close to the build platform. My dual fan cooling is too much airflow close to...
    Post by: cdsl810, Mar 1, 2016 in forum: Troubleshooting
  16. cdsl810
    Post

    Unresolved Filament not getting stuck after first layer

    Loosen the two spring-loaded screws on the filament quick-release a little. If this tension is too high it can put too much pressure on the hobbed...
    Post by: cdsl810, Mar 1, 2016 in forum: Troubleshooting
  17. cdsl810
    Post

    Solved .

    I would make sure the part cooling fan is on full speed while printing PLA (after the first layer if your software will allow it). I haven't had...
    Post by: cdsl810, Mar 1, 2016 in forum: Troubleshooting
  18. cdsl810
    Post

    Solved Thermal Runaway

    I copied my PID settings over to RC3... but... I will re-tune the PID to eliminate that possibility. I have to mention that I have the Printed...
    Post by: cdsl810, Feb 29, 2016 in forum: Troubleshooting
  19. cdsl810
    Thread

    Solved Thermal Runaway

    I just got this error for the first time ever. The print halted and the extruder and bed heater turned off. So, at the very least, this error...
    Thread by: cdsl810, Feb 29, 2016, 13 replies, in forum: Troubleshooting
  20. cdsl810
    Post

    Marlin Firmware Upgrade 1.1.0 RC8 & RCBugFix (For R1 & R1+PLUS)

    It turns out the the BUGFIX version has the Z feedrate set at 4*60 I set it to 10*60 and everything is back to normal functionality. I am...
    Post by: cdsl810, Feb 29, 2016 in forum: Mods and Upgrades
Showing results 1 to 20 of 50 Next >
Search Again
Page 1 of 3