1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
  1. Captain McGillacutty
    Post

    Fans; Single or dual, shroud or no shroud

    Make sure you use shrink tube as well, to make it easier with tiny wires you could make hooks in all three red or black, hook together then GENTLY...
    Post by: Captain McGillacutty, Mar 1, 2016 in forum: Mods and Upgrades
  2. Captain McGillacutty
    Post

    Fans; Single or dual, shroud or no shroud

    [MEDIA]
    Post by: Captain McGillacutty, Mar 1, 2016 in forum: Mods and Upgrades
  3. Captain McGillacutty
    Thread

    Heating up after leveling in Cura

    This is intended for those who have a PEI sheet on their print bed and use Cura. Thanks to Danzca6 for putting another pair of eyes on it and...
    Thread by: Captain McGillacutty, Feb 27, 2016, 0 replies, in forum: Software
  4. Captain McGillacutty
    Post

    Solved Heater foil tape

    That was mine first day... I did the same thing as Jeff.
    Post by: Captain McGillacutty, Feb 24, 2016 in forum: Troubleshooting
  5. Captain McGillacutty
    Post

    New Stabilizer

    I do understand the volume. Though the stability through midrange is the goal. If you are printing tall they are made to be removed very easily,...
    Post by: Captain McGillacutty, Feb 24, 2016 in forum: Mods and Upgrades
  6. Captain McGillacutty
    Post

    New Stabilizer

    it makes the thread and stabilizer solid.
    Post by: Captain McGillacutty, Feb 23, 2016 in forum: Mods and Upgrades
  7. Captain McGillacutty
    Thread

    New Stabilizer

    http://www.thingiverse.com/thing:1358304
    Thread by: Captain McGillacutty, Feb 20, 2016, 5 replies, in forum: Mods and Upgrades
  8. Captain McGillacutty
    Thread

    Fans; Single or dual, shroud or no shroud

    I followed a couple videos before receiving my Robo R1+. I went with the dual 40 by 20 fans and ran into failure. I downgraded to single and...
    Thread by: Captain McGillacutty, Feb 20, 2016, 25 replies, in forum: Mods and Upgrades
  9. Captain McGillacutty
    Thread

    Hello

    Just bought my first 3D printer 2 weeks ago. I can say the Robo was the right choice, entry price was good and enough to tinker with and upgrade...
    Thread by: Captain McGillacutty, Feb 20, 2016, 1 replies, in forum: United States of America
  10. Captain McGillacutty
    Post

    Solved Heater foil tape

    Thanks, I was hoping I could replace it with a standard tape.
    Post by: Captain McGillacutty, Feb 18, 2016 in forum: Troubleshooting
  11. Captain McGillacutty
    Post

    convert robo3d into cnc

    You could use a Dremel and slow the speed. The best way is print the parts needed, check out novice experts vids for arduino and do to...
    Post by: Captain McGillacutty, Feb 17, 2016 in forum: General Questions
  12. Captain McGillacutty
    Thread

    Solved Heater foil tape

    My adhesive gets warm and allows the tape to droop enough to catch the belt bolts. Anyone have a tested fix for this issue?
    Thread by: Captain McGillacutty, Feb 17, 2016, 12 replies, in forum: Troubleshooting
Showing results 1 to 12 of 12
Search Again