1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
  1. Just Kelly
    Post

    Solved Right Z-axis motor won't turn

    OK, took it to the local printer doc and we worked it out. The right lead screw was gummed up with somethingorother which was keeping things from...
    Post by: Just Kelly, Oct 25, 2017 in forum: Troubleshooting
  2. Just Kelly
    Post

    Solved Right Z-axis motor won't turn

    I see. I don't suppose there's a nice video out there showing how to swap out the z-motors on the plus? Or even a nice doc with photos? Haven't...
    Post by: Just Kelly, Oct 18, 2017 in forum: Troubleshooting
  3. Just Kelly
    Post

    Solved Right Z-axis motor won't turn

    OK, so I swapped out the left & right z-motor connections on the main board to see if it made a difference. It didn't: left still fine, right...
    Post by: Just Kelly, Oct 17, 2017 in forum: Troubleshooting
  4. Just Kelly
    Post

    Solved Right Z-axis motor won't turn

    OK, reseated all motor connections and such, and it's still misbehaving. I think it's probably easier to show than to describe, so here's a video:...
    Post by: Just Kelly, Oct 16, 2017 in forum: Troubleshooting
  5. Just Kelly
    Thread

    Solved Right Z-axis motor won't turn

    It seems every time I print something tall, I wind up with a z-axis issue. This time, the right-hand motor refuses to turn, so when I try to get...
    Thread by: Just Kelly, Oct 16, 2017, 14 replies, in forum: Troubleshooting
  6. Just Kelly
    Post

    Answered Broken part, fixable?

    Uhm, ok. Where are the z-switches at, exactly?
    Post by: Just Kelly, Sep 9, 2017 in forum: Troubleshooting
  7. Just Kelly
    Post

    Answered Broken part, fixable?

    OK, got the clamp back into position, and tweaked the z-rods to as close to even as I could eyeball, but now when I fire this thing up it doesn't...
    Post by: Just Kelly, Sep 9, 2017 in forum: Troubleshooting
  8. Just Kelly
    Thread

    Answered Broken part, fixable?

    So I started my print before I went out to run errands, and when I came back the print carriage was all the way at the top of the Z axis. When I...
    Thread by: Just Kelly, Sep 9, 2017, 6 replies, in forum: Troubleshooting
  9. Just Kelly
    Post

    Unanswered R1+ Hotend clogged, now MINTEMP triggered

    Now, is the thermistor the little tiny thing in the hotend or the larger cylinder? Because the cylinder came out when I was removing the hotend,...
    Post by: Just Kelly, May 18, 2016 in forum: Troubleshooting
  10. Just Kelly
    Thread

    Unanswered R1+ Hotend clogged, now MINTEMP triggered

    OK, so I had some PLA get stuck in my hot end and it broke off while I was trying to pull it out (it won't budge even with the extruder temp @...
    Thread by: Just Kelly, May 15, 2016, 5 replies, in forum: Troubleshooting
  11. Just Kelly
    Post

    Partially Solved Calibrating seems to be off on Y axis

    It doesn't, huh? Color me surprised. Well, still getting the occasional bit of lift when it goes across the line, but I suppose I can just brim it...
    Post by: Just Kelly, Mar 19, 2016 in forum: Troubleshooting
  12. Just Kelly
    Post

    Partially Solved Calibrating seems to be off on Y axis

    My Y center is a bit off as well. Not usually a problem, but I'm doiong some longer pritns lately and so I wind up with one end hanging over the...
    Post by: Just Kelly, Mar 18, 2016 in forum: Troubleshooting
  13. Just Kelly
    Post

    Solved Loose part?

    Oh, okay! *whew* Just as long as it's not vital or something. I was going to say it didn't seem to affect last night's prints. Anyway, thanks for...
    Post by: Just Kelly, Mar 7, 2016 in forum: Troubleshooting
  14. Just Kelly
    Thread

    Solved Loose part?

    I was taking a print off the machine this morning, and I noticed back in the side off the frame and all that a loose piece (photo enclosed). I...
    Thread by: Just Kelly, Mar 7, 2016, 3 replies, in forum: Troubleshooting
  15. Just Kelly
    Post

    PLA Microcenter Inland PLA

    Yeah, I wound up getting one a couple weeks ago. Solid as a freaking rock. Puts my old i3 to shame. I've used mostly Inland PLA with it so far...
    Post by: Just Kelly, Mar 4, 2016 in forum: Printing Filament
  16. Just Kelly
    Post

    PLA Microcenter Inland PLA

    Hi. I'm thinking very hard about picking up the r1 plus on Friday, mostly using Inland as Microcenter is available locally. What do you find works...
    Post by: Just Kelly, Feb 15, 2016 in forum: Printing Filament
Showing results 1 to 16 of 16
Search Again