1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
  1. greif07
    Post

    Unanswered Bumps. Horizontal layers and nozzle bouncing.

    I have none of these issues when I print a calibration cube. The cube has a much thinner wall of course, so I have experimented with my layer...
    Post by: greif07, Apr 6, 2016 in forum: Troubleshooting
  2. greif07
    Post

    Partial Answer Bed heats up then it shuts down

    What version of the printer do you have? Is the power and thermistor cable flat and feeding out the back or is there a molex-style connector hot...
    Post by: greif07, Apr 6, 2016 in forum: Troubleshooting
  3. greif07
    Post

    Unanswered Adjusting Z Endstop for Leveling?

    Just my preference.. I use the M565 code for the Z offset. I found that MC didn't seem consistent with the Z offset setting. Since I occasionally...
    Post by: greif07, Apr 6, 2016 in forum: Troubleshooting
  4. greif07
    Post

    Unresolved Getting really frustrated

    A couple of somewhat related issues I had; Remove the two spring-loaded screws that hold in the piece that pressures the filament. Once you have...
    Post by: greif07, Apr 6, 2016 in forum: Troubleshooting
  5. greif07
    Post

    Answered Print location is different from what is shown in mattercontrol

    I'm not using MatterControl.. but under Settings and Controls > Printer > Print Area, you should see 228 x 254 for dimensions and 114 x 127 for...
    Post by: greif07, Apr 6, 2016 in forum: Troubleshooting
  6. greif07
    Post

    Solved Something crazy just happened with my Robo 3D Plus

    I'm sure lots of people have had success with cheap Chinese knockoff 2560 boards on Amazon, but I haven't. After a few days of frustration and...
    Post by: greif07, Apr 6, 2016 in forum: Troubleshooting
  7. greif07
    Post

    Solved Can anyone tell me whats going on here???

    Have you raised the bed temp? I saw 45 in your screenshot but I usually get great results at 60 w/PLA. I've been having all kinds of issues lately...
    Post by: greif07, Apr 6, 2016 in forum: Troubleshooting
  8. greif07
    Thread

    Unanswered Bumps. Horizontal layers and nozzle bouncing.

    Greetings. I've been trying to print a file in ABS. The issue I'm having is that the ABS is globbing bumps when traveling X. I've changed...
    Thread by: greif07, Apr 6, 2016, 1 replies, in forum: Troubleshooting
  9. greif07
    Post

    Solved Misaligned/missed layers only on one side?

    Yeah it doesn't seem to like the dry PTFE lube. I've got 3-in-1 and white grease. Lesson learned haha.
    Post by: greif07, Mar 9, 2016 in forum: Troubleshooting
  10. greif07
    Post

    Solved Misaligned/missed layers only on one side?

    Also, I only used dry PTFE lube on the guide rods.
    Post by: greif07, Mar 9, 2016 in forum: Troubleshooting
  11. greif07
    Post

    Solved Misaligned/missed layers only on one side?

    It appears that my linear bearings were shot on the Y and not suddenly the Z bearings are also making lovely sounds. I ordered a dozen. After...
    Post by: greif07, Mar 9, 2016 in forum: Troubleshooting
  12. greif07
    Post

    Solved Misaligned/missed layers only on one side?

    I'll print a flip. I've got a fan on both sides.
    Post by: greif07, Mar 8, 2016 in forum: Troubleshooting
  13. greif07
    Post

    Solved Misaligned/missed layers only on one side?

    I've printed about 8 parts and anything over about 5mm in height has the same issue on the back side. I did run at 108% extrusion on a few and...
    Post by: greif07, Mar 8, 2016 in forum: Troubleshooting
  14. greif07
    Thread

    Solved Misaligned/missed layers only on one side?

    Hello! I recently acquired a Robo R1. I've had to do a lot of work on it (lead screw upgrade, new Arduino and RAMPS boards, new cable for heated...
    Thread by: greif07, Mar 8, 2016, 9 replies, in forum: Troubleshooting
Showing results 1 to 14 of 14
Search Again