1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
  1. Fruition_Factory
    Thread

    Unresolved Replacment nuts for z axis lead screw.

    I am trying to find replacement hex nuts for the 8mm lead screw on the printers Z axis. I lost one in transit and am unable to find another one...
    Thread by: Fruition_Factory, Mar 13, 2017, 3 replies, in forum: Troubleshooting
  2. Fruition_Factory
    Thread

    Unanswered Scripted filament change R1/S3D

    I have a large number of parts (all the same) that i need to print using 2 colors. For the past week i have been waiting impatiently and using the...
    Thread by: Fruition_Factory, Dec 23, 2016, 1 replies, in forum: General Questions
  3. Fruition_Factory
    Thread

    S3D end Gcode

    When i slice with cura or matter control at the end of the print it moves the tool to home on the X&Y, for some reason now with S3D it just leaves...
    Thread by: Fruition_Factory, May 14, 2016, 3 replies, in forum: Software
  4. Fruition_Factory
    Thread

    Simplify 3D Manual Configuration Settings

    Hey guys, My S3D is on the fritz and its been over 40 hours and no word back from support yet to help me get back up and printing. Had to crack it...
    Thread by: Fruition_Factory, May 12, 2016, 12 replies, in forum: Software
  5. Fruition_Factory
    Thread

    Solved No z axis control on rrdiscount full graphics LCD?

    Not sure if its standard with the lcd but after installing it and flashing the firmware with the sd support and correct lcd un-commented i noticed...
    Thread by: Fruition_Factory, Apr 11, 2016, 4 replies, in forum: Troubleshooting
  6. Fruition_Factory
    Thread

    How many watts is the R1 Power Supply?

    Title says it all. Anyone know off hand? Trying to eventually calculate cost/hr to operate, but want to start with how many watts the PSU is. Thanks
    Thread by: Fruition_Factory, Apr 3, 2016, 4 replies, in forum: General Questions
  7. Fruition_Factory
    Thread

    Solved Issue with Cura 15 and R1

    Tiny problem, but need a solution. I have a model, its size is 240x189x84, well small enough to barley fit on the R1. When i load the model into...
    Thread by: Fruition_Factory, Apr 3, 2016, 4 replies, in forum: Troubleshooting
  8. Fruition_Factory
    Thread

    Solved Which pins for the bottom case fan?

    Can anyone tell me or show a picture of which pins the power is suppose to connect to for the fan that is in the base of the unit cooling the cpu....
    Thread by: Fruition_Factory, Mar 29, 2016, 4 replies, in forum: Troubleshooting
  9. Fruition_Factory
    Thread

    Solved ABS on with the factory hex hotend?

    Just got a dozen rolls of some good ABS, I have not upgraded the hot end to the E3D V6 as I don't feel it is necessary until the factory one...
    Thread by: Fruition_Factory, Mar 20, 2016, 20 replies, in forum: General Questions
  10. Fruition_Factory
    Thread

    Solved Y axis jumps, sticks, screws up 90% of prints.

    So, after a week of having to print upgrades for the R1 so it would function without troubles. (cable chain, spool holder, etc) I finally get to...
    Thread by: Fruition_Factory, Mar 18, 2016, 14 replies, in forum: Troubleshooting
  11. Fruition_Factory
    Thread

    500mm Z Mod - Stage 1 - Planning

    After a weekend of exploring and tinkering, i have concluded that building risers for the cover to lift it that high is as simple as pressing...
    Thread by: Fruition_Factory, Mar 13, 2016, 2 replies, in forum: Mods and Upgrades
  12. Fruition_Factory
    Thread

    Solved Print stops a few minutes in every time

    Not off to the best first day with the R1. Finally got it to print on the bed using an older version of cura but now it stops on every print about...
    Thread by: Fruition_Factory, Mar 7, 2016, 8 replies, in forum: Troubleshooting
  13. Fruition_Factory
    Thread

    Solved Printing in the air

    So my printer arrived today, figured i would set it up and try it out quick and the thing refuses to print on the plate. I have tried MC & Cura...
    Thread by: Fruition_Factory, Mar 7, 2016, 5 replies, in forum: Troubleshooting
  14. Fruition_Factory
    Thread

    Answered Can anyone reccomend a slicer that is not S3D?

    I just purchased an R1 that will be here this coming Monday, from what i learned in doing some online research the slicer software that comes with...
    Thread by: Fruition_Factory, Mar 3, 2016, 43 replies, in forum: General Questions
Showing results 1 to 14 of 14
Search Again