1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 1 of 3
  1. Jeff Hamilton
    Post

    Unresolved Print head not raising at end of print

    Thank you very much. I knew I was missing something but I couldn't figure it out. Most of my parts are short so the 30mm lift worked, now with the...
    Post by: Jeff Hamilton, Apr 29, 2021 in forum: Troubleshooting
  2. Jeff Hamilton
    Thread

    Unresolved Print head not raising at end of print

    I am really confused. My print head is dropping by about 1mm at the end of the print and damaging the print rather than raising up before moving....
    Thread by: Jeff Hamilton, Apr 29, 2021, 2 replies, in forum: Troubleshooting
  3. Jeff Hamilton
    Post

    Solved Printer not responding

    Well it did end up being that I had uploaded a program I was working on to the 3d printer. It was real fun re-installing everything since I had...
    Post by: Jeff Hamilton, Jun 12, 2018 in forum: Troubleshooting
  4. Jeff Hamilton
    Post

    Solved Printer not responding

    The printer was not plugged in while I was working on another project. What do I look at to see if the board went bad?
    Post by: Jeff Hamilton, Jun 12, 2018 in forum: Troubleshooting
  5. Jeff Hamilton
    Thread

    Solved Printer not responding

    Went to use my printer today after a couple of weeks and when I start Mattercontrol and try to connect it says "Invalid Printer Response" and...
    Thread by: Jeff Hamilton, Jun 12, 2018, 4 replies, in forum: Troubleshooting
  6. Jeff Hamilton
    Post

    Answered ABS barrel print problems

    Got the larger section to print better, but the small top section would always turn out muddy even though I slowed it down. So I gave up and...
    Post by: Jeff Hamilton, Feb 21, 2018 in forum: Troubleshooting
  7. Jeff Hamilton
    Post

    Answered ABS barrel print problems

    That helped a little on the top but the seem in the side got worse. Going to try and randomize the start points as Mark suggested and drop temp to 225
    Post by: Jeff Hamilton, Feb 21, 2018 in forum: Troubleshooting
  8. Jeff Hamilton
    Thread

    Answered ABS barrel print problems

    I am using S3D to print this 12mm x 21mm tall hollow barrel and I can't seem to figure out what I am doing wrong. I am printing at 230 with a 90c...
    Thread by: Jeff Hamilton, Feb 21, 2018, 5 replies, in forum: Troubleshooting
  9. Jeff Hamilton
    Post

    Solved PETG filament adjustment suggestions

    Changed to the 910 and after several attempts working with the supports and the temp I finally got it right. I had the temp at 250 when I tried...
    Post by: Jeff Hamilton, Feb 20, 2018 in forum: Troubleshooting
  10. Jeff Hamilton
    Post

    Solved PETG filament adjustment suggestions

    Thank you, I'll give it a try.
    Post by: Jeff Hamilton, Feb 19, 2018 in forum: Troubleshooting
  11. Jeff Hamilton
    Post

    Solved PETG filament adjustment suggestions

    Mark, I have some 910 would you share your setting so I can give that a try?
    Post by: Jeff Hamilton, Feb 19, 2018 in forum: Troubleshooting
  12. Jeff Hamilton
    Post

    Solved PETG filament adjustment suggestions

    Thank you. I didn't fully understand what you wrote, but I got it now. I have been slowly making changes to make improvements but I haven't hit...
    Post by: Jeff Hamilton, Feb 19, 2018 in forum: Troubleshooting
  13. Jeff Hamilton
    Post

    Solved PETG filament adjustment suggestions

    What numbers are you using in the calculator? Using .14 I see an error so I must be doing something wrong.
    Post by: Jeff Hamilton, Feb 19, 2018 in forum: Troubleshooting
  14. Jeff Hamilton
    Thread

    Solved PETG filament adjustment suggestions

    I'm working on the small part and I'm have a little difficulty getting my setting right. I am using S3D, with E3D V6 head on a Robo 1+, printing...
    Thread by: Jeff Hamilton, Feb 19, 2018, 14 replies, in forum: Troubleshooting
  15. Jeff Hamilton
    Post

    Another printer (it is a disease, once you start collecting them...)

    I'm using the Wolfbite in the red bottle for ABS and to tell you the truth it is really hit and miss. I have re-cleaned the bed applied as...
    Post by: Jeff Hamilton, Apr 28, 2017 in forum: Projects
  16. Jeff Hamilton
    Post

    Solved NijaFlex through a Titan Extruder with E3DV6 Hot End

    Well my other shipment didn't arrive today so I decided to give NijaFlex another try and I am happy to say I finally had success. Here are the...
    Post by: Jeff Hamilton, Mar 13, 2017 in forum: Troubleshooting
  17. Jeff Hamilton
    Post

    Solved NijaFlex through a Titan Extruder with E3DV6 Hot End

    Well after MANY attempts and varying settings and not one complete print I have come to the conclusion that the Titan extruder will not print with...
    Post by: Jeff Hamilton, Mar 13, 2017 in forum: Troubleshooting
  18. Jeff Hamilton
    Post

    Solved NijaFlex through a Titan Extruder with E3DV6 Hot End

    I have dropped the tube so it is just above the hob and that leaves very little area without tubing. Slowed the speed down to 10 mm/s and...
    Post by: Jeff Hamilton, Mar 13, 2017 in forum: Troubleshooting
  19. Jeff Hamilton
    Post

    Solved NijaFlex through a Titan Extruder with E3DV6 Hot End

    I drilled out the feeder section and ran the tube down to just above the hob tension roller, then I changed the nozzle to a .50 and slowed the...
    Post by: Jeff Hamilton, Mar 13, 2017 in forum: Troubleshooting
  20. Jeff Hamilton
    Post

    Solved NijaFlex through a Titan Extruder with E3DV6 Hot End

    I can't see where the Nijaflex is coming out of, but when I noticed it had stopped printing there was a section of the nijaflex sticking out the...
    Post by: Jeff Hamilton, Mar 12, 2017 in forum: Troubleshooting
Showing results 1 to 20 of 43 Next >
Search Again
Page 1 of 3