1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 1 of 2
  1. XEMA
    Post

    Community Favorite Marlin 1.1.7 Release for Robo R1, R1+PLUS & Variants

    What are you using for your values? Somewhere for me to start.... Sent from my Pixel XL using Tapatalk
    Post by: XEMA, Mar 6, 2018 in forum: Mods and Upgrades
  2. XEMA
    Post

    Community Favorite Marlin 1.1.7 Release for Robo R1, R1+PLUS & Variants

    That's what I thought too, I have changed it from the -1.00 all the way to 0, doesn't seem to help. I will try the firmware this time. Sent from...
    Post by: XEMA, Mar 6, 2018 in forum: Mods and Upgrades
  3. XEMA
    Post

    Community Favorite Marlin 1.1.7 Release for Robo R1, R1+PLUS & Variants

    You think it would help solve my issue by changing the offset in the firmware? I have tried changing it via the LCD and the m851 command. Sent...
    Post by: XEMA, Mar 6, 2018 in forum: Mods and Upgrades
  4. XEMA
    Post

    Community Favorite Marlin 1.1.7 Release for Robo R1, R1+PLUS & Variants

    on 1.1.8 (R1+) as well, I can get to the point where I start printing the validation mesh pattern, but the nozzle is too close to the bed. Any...
    Post by: XEMA, Mar 6, 2018 in forum: Mods and Upgrades
  5. XEMA
    Post

    PET First print with PETG - thoughts?

    Looks good, but I would mess around with the temperatures, it appears as though you are running it a tad hot. When I run the transparent PETG, I...
    Post by: XEMA, Aug 2, 2016 in forum: Printing Filament
  6. XEMA
    Post

    Octoprint question

    I know this doesn't help too much, but I slice my STL's with S3D and upload them/print with no issues at all. Yes, remove that line you mentioned...
    Post by: XEMA, May 17, 2016 in forum: Mods and Upgrades
  7. XEMA
    Thread

    Unanswered Paint on underside of build plate?

    Anyone know what type of paint is used for the graphics on the underside of the glass build plate? Also, has anyone heard of anyone creating a...
    Thread by: XEMA, Apr 29, 2016, 3 replies, in forum: General Questions
  8. XEMA
    Thread

    Spaceclaim with STL Prep

    Wasn't able to find any other threads on this software package so figured I would post my 2 cents. I did the 15 day trial and liked it enough to...
    Thread by: XEMA, Apr 29, 2016, 0 replies, in forum: Software
  9. XEMA
    Thread

    Unanswered Lost Magnet - Replacement?

    So one of my magnets apparently wasn't glued in properly and has popped out and subsequently been lost. Does anyone know where I can get an exact...
    Thread by: XEMA, Apr 14, 2016, 2 replies, in forum: Troubleshooting
  10. XEMA
    Post

    First test of FLEKS 3D build plate kit

    Try heating it up on your bed/plate first, then gently but firmly flexing out the warp. If the center is high, put your thumbs on the high side...
    Post by: XEMA, Apr 11, 2016 in forum: Show and Tell
  11. XEMA
    Post

    First test of FLEKS 3D build plate kit

    I wouldn't give up on them, the one time I contacted them it did take awhile, but they did get back to me. Regarding the warped issue. Have you...
    Post by: XEMA, Apr 11, 2016 in forum: Show and Tell
  12. XEMA
    Post

    First test of FLEKS 3D build plate kit

    Here is the clip I re-designed based on one I found: http://www.thingiverse.com/thing:1465977 *Note: If printed properly, they should just clear...
    Post by: XEMA, Apr 4, 2016 in forum: Show and Tell
  13. XEMA
    Post

    Have I missed any modifications to my Robo R1+?

    Check out this thread
    Post by: XEMA, Apr 4, 2016 in forum: Show and Tell
  14. XEMA
    Post

    First test of FLEKS 3D build plate kit

    Are you saying that during the auto bed level portion it heated and went through the bed? You have to change the startup script so the extruder...
    Post by: XEMA, Mar 31, 2016 in forum: Show and Tell
  15. XEMA
    Post

    Have I missed any modifications to my Robo R1+?

    It is by no means perfect but it does work pretty well. ABS can be printed without heat but it is still temperamental at times with warping. PLA...
    Post by: XEMA, Mar 29, 2016 in forum: Show and Tell
  16. XEMA
    Post

    Have I missed any modifications to my Robo R1+?

    Here is the 10x10 Fleks3D plate and frame mounted on the R1+ [IMG]
    Post by: XEMA, Mar 29, 2016 in forum: Show and Tell
  17. XEMA
    Post

    Have I missed any modifications to my Robo R1+?

    The 10x10 with the frame fits perfectly. The outside of the frame is flush with the glass.
    Post by: XEMA, Mar 29, 2016 in forum: Show and Tell
  18. XEMA
    Post

    First test of FLEKS 3D build plate kit

    The corners tend to come up above the frame when printing in my experience. I made some clips to put around it so the plate remains as flat as...
    Post by: XEMA, Mar 28, 2016 in forum: Show and Tell
  19. XEMA
    Post

    Unresolved Bad Stepper?

    Thanks for the feedback, I am going to engage the warranty site and see about getting a replacement.
    Post by: XEMA, Mar 28, 2016 in forum: Troubleshooting
  20. XEMA
    Post

    First test of FLEKS 3D build plate kit

    I know what you mean, luckily mine crater is right next the the thumbhole so it isn't too bad. Definitely set the GCode to head up the extruder...
    Post by: XEMA, Mar 26, 2016 in forum: Show and Tell
Showing results 1 to 20 of 27 Next >
Search Again
Page 1 of 2