1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 1 of 3
  1. Wild8Wire
    Post

    Solved Belt Tension

    If can tell in the pic, belt goes over the square part of the carriage; zip tie goes through the hole in that square, and wraps around the belt on...
    Post by: Wild8Wire, Jul 3, 2016 in forum: Troubleshooting
  2. Wild8Wire
    Post

    Solved Belt Tension

    Hope this helps; blurry because it's running. Took mine apart for the same reason, but put it back the way it came:[IMG]
    Post by: Wild8Wire, Jul 3, 2016 in forum: Troubleshooting
  3. Wild8Wire
    Post

    Unresolved leveling help

    Manually leveling the bed (turning the z-axis rods by hand, mentioned above) works well along the X-axis. But I think what happened here is the...
    Post by: Wild8Wire, Jul 3, 2016 in forum: Troubleshooting
  4. Wild8Wire
    Post

    What is the best way to remove the heating element from the glass?

    Thanks for the suggestions! The double-sided tape might work, if the cork board is only sagging and not expanding. The PEI sheet is definitely...
    Post by: Wild8Wire, Jun 1, 2016 in forum: Mods and Upgrades
  5. Wild8Wire
    Post

    What is the best way to remove the heating element from the glass?

    Interesting; thanks for clarifying. I've got a replacement cork board coming because mine keeps sagging, and scraping the bolt heads. Seems like...
    Post by: Wild8Wire, May 31, 2016 in forum: Mods and Upgrades
  6. Wild8Wire
    Post

    What is the best way to remove the heating element from the glass?

    Earlier posts were discussing the cork. What's the purpose of the cork? Is it just an insulator to prevent the heating element from touching the...
    Post by: Wild8Wire, May 31, 2016 in forum: Mods and Upgrades
  7. Wild8Wire
    Post

    Partially Solved Broken Glass on The Heated Bed

    Glad I'm not the only one with this issue (meaning I didn't think I abused it). [emoji6] Ran a print this morning, and when prying the piece off...
    Post by: Wild8Wire, May 28, 2016 in forum: Troubleshooting
  8. Wild8Wire
    Post

    Unresolved X-Axis bouncing?

    Thanks (both of you) for the replies. I didn't figure there was a good fix, but yah, curved glass is what I figured. The auto-leveling helps,...
    Post by: Wild8Wire, May 22, 2016 in forum: Troubleshooting
  9. Wild8Wire
    Post

    Unresolved X-Axis bouncing?

    Hijacking my own thread. [emoji6] Since we're on bed leveling, any suggestions for adjusting the level of the center is high? I've "paper...
    Post by: Wild8Wire, May 22, 2016 in forum: Troubleshooting
  10. Wild8Wire
    Post

    Unresolved XXL controller button stops working?

    Thanks for the replies. Forgot Printed Solid was on here, and I've already sent an e-mail on the issue. [emoji1303] Already...
    Post by: Wild8Wire, May 3, 2016 in forum: Troubleshooting
  11. Wild8Wire
    Post

    Unresolved XXL controller button stops working?

    Did that right before posting; no luck [emoji22]
    Post by: Wild8Wire, May 2, 2016 in forum: Troubleshooting
  12. Wild8Wire
    Thread

    Unresolved XXL controller button stops working?

    I've got a reprap XXL controller which I've been using for about 3 weeks (and really like), but yesterday, the knob button (push to select)...
    Thread by: Wild8Wire, May 2, 2016, 7 replies, in forum: Troubleshooting
  13. Wild8Wire
    Post

    Solved ROBO 3d R1 Plus new issue.

    Agree with Geof, based on personal experience [emoji37] Mine sucked up a small piece of plastic, jamming the fan blade; removed the jam, and ran...
    Post by: Wild8Wire, May 2, 2016 in forum: Troubleshooting
  14. Wild8Wire
    Post

    Free 3D software to edit STL files?

    Thanks for the vid! I like Makers Muse vids. [emoji1303] Some useful info there, but still doesn't quite address what I'm wanting to do....
    Post by: Wild8Wire, Apr 24, 2016 in forum: General Questions
  15. Wild8Wire
    Post

    Free 3D software to edit STL files?

    I understand that one. My problem is pulling files from somewhere like DestinySTLGenerator, where it takes the files from the in-game models. I...
    Post by: Wild8Wire, Apr 22, 2016 in forum: General Questions
  16. Wild8Wire
    Post

    Free 3D software to edit STL files?

    Thanks for the replies. [emoji1303] I'll check into both and give them a try
    Post by: Wild8Wire, Apr 22, 2016 in forum: General Questions
  17. Wild8Wire
    Post

    Free 3D software to edit STL files?

    Not what I was hoping to hear, but pretty much what I expected. [emoji6] I'd love to have real 3D files to modify; but short of redesigning them...
    Post by: Wild8Wire, Apr 21, 2016 in forum: General Questions
  18. Wild8Wire
    Thread

    Free 3D software to edit STL files?

    Anyone know of a 3D program (preferably freeware) that will allow editing of an STL file? I used Netfabb Basic to cut a large STL into sections...
    Thread by: Wild8Wire, Apr 21, 2016, 10 replies, in forum: General Questions
  19. Wild8Wire
    Post

    Unresolved X-Axis bouncing?

    Since a few people offered suggestions, and others may run into this problem, I wanted to post what worked on my machine... But for now, it'll...
    Post by: Wild8Wire, Apr 16, 2016 in forum: Troubleshooting
  20. Wild8Wire
    Post

    Unresolved X-Axis bouncing?

    Thanks for the suggestion! Think I remember reading that (your, or someone else's, post). Tech support e-mailed me back and suggestion...
    Post by: Wild8Wire, Apr 15, 2016 in forum: Troubleshooting
Showing results 1 to 20 of 41 Next >
Search Again
Page 1 of 3