1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
  1. Curgon
    Post

    Unanswered T-Glase not sticking

    Sorry for not getting back. Your help and settings helped me get in a good direction! Next thing to learn, properly cleaning of the nozzle.
    Post by: Curgon, Mar 30, 2016 in forum: Troubleshooting
  2. Curgon
    Post

    Unanswered T-Glase not sticking

    Well my friends, you were very helpful. Only problem left to troubleshoot, was why simplyfy3D keeps stopping like 2-3 layers in, the start and END...
    Post by: Curgon, Mar 23, 2016 in forum: Troubleshooting
  3. Curgon
    Post

    Unanswered T-Glase not sticking

    Ah ok, do you have a sample syntax I could use and just change the value to what I need?
    Post by: Curgon, Mar 23, 2016 in forum: Troubleshooting
  4. Curgon
    Post

    Unanswered T-Glase not sticking

    Are the offsets defined in Simplfy3D somewhere by chance?
    Post by: Curgon, Mar 23, 2016 in forum: Troubleshooting
  5. Curgon
    Post

    Unanswered T-Glase not sticking

    Yeah, the offset is what has me confused since its auto leveling. I am not sure how or where I would start to adjust that, or if its even needed.
    Post by: Curgon, Mar 23, 2016 in forum: Troubleshooting
  6. Curgon
    Post

    Unanswered T-Glase not sticking

    I current use painters tape, with hairspray on it. Would you advise differently?
    Post by: Curgon, Mar 23, 2016 in forum: Troubleshooting
  7. Curgon
    Post

    Unanswered T-Glase not sticking

    I will attempt it again tonight, with the glass and with the double sided tape, and will report back my results.
    Post by: Curgon, Mar 23, 2016 in forum: Troubleshooting
  8. Curgon
    Post

    Unanswered T-Glase not sticking

    And once I get home from work, I will try the suggest temp for the bed, or the average and use some glue. :)
    Post by: Curgon, Mar 23, 2016 in forum: Troubleshooting
  9. Curgon
    Post

    Unanswered T-Glase not sticking

    Ah thanks Mark, I was looking for it last night and must have missed it. I think the other settings are easier to find that he has displayed in...
    Post by: Curgon, Mar 23, 2016 in forum: Troubleshooting
  10. Curgon
    Post

    Unanswered T-Glase not sticking

    Yeah I will need to dig in the settings for to set the first layer to print slower, so your speed averaged from 30-40 mms?
    Post by: Curgon, Mar 23, 2016 in forum: Troubleshooting
  11. Curgon
    Post

    Unanswered T-Glase not sticking

    And all you did was use elmer glue stick on the plate? Any temp on that? What is the max I should take my board to?
    Post by: Curgon, Mar 23, 2016 in forum: Troubleshooting
  12. Curgon
    Post

    Unanswered T-Glase not sticking

    Yeah I got the extruder looking good, I just wanted to know how to get it to STICK! Lol. Ive had someone suggest to me double sided tape, I was...
    Post by: Curgon, Mar 23, 2016 in forum: Troubleshooting
  13. Curgon
    Post

    Unanswered T-Glase not sticking

    Ive had PLA prints before, worked just fine. I am currently using Simplfy3D.
    Post by: Curgon, Mar 23, 2016 in forum: Troubleshooting
  14. Curgon
    Post

    Unanswered T-Glase not sticking

    It would be most appreciated, I am not new to 3D printing too much, just T-Glase, and its my first attempt.
    Post by: Curgon, Mar 22, 2016 in forum: Troubleshooting
  15. Curgon
    Post

    Unanswered T-Glase not sticking

    Did you have a glass bed temp? Can you be more specific?
    Post by: Curgon, Mar 22, 2016 in forum: Troubleshooting
  16. Curgon
    Thread

    Unanswered T-Glase not sticking

    Not sure if this may be the correct area to post. But here goes.... I have a R1+, using red T-Glase. When printing on tape or glase, It doesnt...
    Thread by: Curgon, Mar 22, 2016, 35 replies, in forum: Troubleshooting
Showing results 1 to 16 of 16
Search Again