1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 1 of 2
  1. Jason Hough
    Post

    Cura 2.5

    Unfortunately I can't confirm these work because my printer is non-functional right now, but you're welcome to try them: Start Gcode: G21...
    Post by: Jason Hough, Oct 28, 2017 in forum: Software
  2. Jason Hough
    Thread

    Answered Filament grinding

    I know this has been asked before, but I can't seem to find much consensus on what worked for people or which solution is best. My latest print...
    Thread by: Jason Hough, Sep 14, 2017, 2 replies, in forum: Troubleshooting
  3. Jason Hough
    Post

    Solved Hot end pressing into print

    Just wanted to thank everyone for the suggestions. This turned out to be due to insufficient cooling. I've printed/installed a fan shroud and now...
    Post by: Jason Hough, Sep 12, 2017 in forum: Troubleshooting
  4. Jason Hough
    Post

    Cura 2.5

    Sorry for the delayed reply, @WheresWaldo It has these settings in the provided profile: X: 225 Y: 245 Z: 210
    Post by: Jason Hough, Sep 11, 2017 in forum: Software
  5. Jason Hough
    Post

    Solved Hot end pressing into print

    Ahhh, I see what you mean now. So even if the z-offset was wrong, it would never print at one height and then later drop down below that. Okay....
    Post by: Jason Hough, Sep 4, 2017 in forum: Troubleshooting
  6. Jason Hough
    Post

    Solved Hot end pressing into print

    Whoa, really? So if the z-offset is the same as the layer height, then layer #2 is printed at the same z as layer #1?
    Post by: Jason Hough, Sep 4, 2017 in forum: Troubleshooting
  7. Jason Hough
    Post

    Solved Hot end pressing into print

    Thanks for the tips. I watched the video and tested my extruder - when I told it to extrude 100mm only 90mm went through, so oddly it seems to be...
    Post by: Jason Hough, Sep 4, 2017 in forum: Troubleshooting
  8. Jason Hough
    Thread

    Solved Hot end pressing into print

    Hey everyone, I've been trying to calibrate my printer since fixing an alignment issue last week (see my other post). So I'm printing Benchy...
    Thread by: Jason Hough, Sep 4, 2017, 8 replies, in forum: Troubleshooting
  9. Jason Hough
    Post

    Solved Alignment issue or am I just paranoid?

    Thanks everyone, that seems to have done the trick!
    Post by: Jason Hough, Sep 1, 2017 in forum: Troubleshooting
  10. Jason Hough
    Post

    Solved Alignment issue or am I just paranoid?

    Okay, I think I got it to moved to the right spot, thanks. I will run a test print to make sure before I mark this solved.
    Post by: Jason Hough, Aug 30, 2017 in forum: Troubleshooting
  11. Jason Hough
    Post

    Solved Alignment issue or am I just paranoid?

    Ah yeah. This is telling for sure. Here's both the left and right side: http://imgur.com/a/r8q8G Any tips on how to fix/adjust would be appreciated.
    Post by: Jason Hough, Aug 30, 2017 in forum: Troubleshooting
  12. Jason Hough
    Post

    Solved Alignment issue or am I just paranoid?

    It's an R1+. Sorry for my lack of knowledge here, which part is the microswitch?
    Post by: Jason Hough, Aug 30, 2017 in forum: Troubleshooting
  13. Jason Hough
    Post

    Solved Alignment issue or am I just paranoid?

    Strange, it looks okay on my screen. Anyway, try here: http://imgur.com/a/iTfYE
    Post by: Jason Hough, Aug 30, 2017 in forum: Troubleshooting
  14. Jason Hough
    Thread

    Solved Alignment issue or am I just paranoid?

    I went to use my printer today and happened to notice that the crossbar (sorry don't know the technical name) looks askew from the print bed...
    Thread by: Jason Hough, Aug 30, 2017, 10 replies, in forum: Troubleshooting
  15. Jason Hough
    Post

    Cura 2.5

    It is set as my machine. The start gcode included for the R1+ seems to be the problem. I replaced it with another set I found on these forums and...
    Post by: Jason Hough, Aug 6, 2017 in forum: Software
  16. Jason Hough
    Post

    Cura 2.5

    It says on the software page: CURA 2.5 FOR ROBO Models: C2, R2, and R1+
    Post by: Jason Hough, Aug 6, 2017 in forum: Software
  17. Jason Hough
    Post

    Cura 2.5

    Did you ever get this working? I downloaded the 2.5 from Robo's site, but when I try to print with it the extruder moves to the back of the build...
    Post by: Jason Hough, Aug 5, 2017 in forum: Software
  18. Jason Hough
    Post

    Octoprint question

    That'd be great, thanks much. I'm using some I found in a forum, and managed to get a good print yesterday after I removed all the temperature...
    Post by: Jason Hough, May 19, 2016 in forum: Mods and Upgrades
  19. Jason Hough
    Post

    Octoprint question

    Thanks for the info. Out of curiosity, are you saying that the temps are baked into the gcode? So if I have a gcode file I sliced a while back,...
    Post by: Jason Hough, May 18, 2016 in forum: Mods and Upgrades
  20. Jason Hough
    Post

    Octoprint question

    Understood! Thanks for the suggestion.
    Post by: Jason Hough, May 18, 2016 in forum: Mods and Upgrades
Showing results 1 to 20 of 25 Next >
Search Again
Page 1 of 2