1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 1 of 2
  1. digitalsolo
    Post

    Marlin Firmware Upgrade 1.1.0 RC8 & RCBugFix (For R1 & R1+PLUS)

    Oh it runs Marlin straight from Ultimaker (my board is a direct clone UM2 Ultimainboard). But it runs 1.0, not 1.1 and porting all of the LCD...
    Post by: digitalsolo, Mar 11, 2017 in forum: Mods and Upgrades
  2. digitalsolo
    Post

    Marlin Firmware Upgrade 1.1.0 RC8 & RCBugFix (For R1 & R1+PLUS)

    Running RC8 with MBL now on my Robo. No issues at all, LCD is working great and printer behavior is excellent. I wish I could get Marlin 1.1...
    Post by: digitalsolo, Mar 11, 2017 in forum: Mods and Upgrades
  3. digitalsolo
    Post

    Marlin Firmware Upgrade 1.1.0 RC8 & RCBugFix (For R1 & R1+PLUS)

    Great, thanks Waldo, I'll give this one a shot. I'm playing with writing a custom firmware for my Ultimaker 2 clone right now, using the UM2+...
    Post by: digitalsolo, Nov 30, 2016 in forum: Mods and Upgrades
  4. digitalsolo
    Post

    Marlin Firmware Upgrade 1.1.0 RC8 & RCBugFix (For R1 & R1+PLUS)

    I need to upgrade to RC7... I've been on RC6 since release and, aside from stupid things I've done, I've never had a failed print since....
    Post by: digitalsolo, Sep 1, 2016 in forum: Mods and Upgrades
  5. digitalsolo
    Post

    Marlin Firmware Upgrade 1.1.0 RC8 & RCBugFix (For R1 & R1+PLUS)

    MESH replaces ABL with a manually created "mesh" layout that can probe up to 49 points (probably overkill unless your print bed is a rough hewn...
    Post by: digitalsolo, May 3, 2016 in forum: Mods and Upgrades
  6. digitalsolo
    Post

    Marlin Firmware Upgrade 1.1.0 RC8 & RCBugFix (For R1 & R1+PLUS)

    I did a few short prints to check on the "hang" behavior. No further issues. I'm pretty confident in saying it was a bad slicer save; S3D was...
    Post by: digitalsolo, Apr 29, 2016 in forum: Mods and Upgrades
  7. digitalsolo
    Post

    Marlin Firmware Upgrade 1.1.0 RC8 & RCBugFix (For R1 & R1+PLUS)

    I have only had one issue with RC6 thus far and it may have been a bad file on the SD card. Went to kick off a print via SD and it kicked my G29...
    Post by: digitalsolo, Apr 28, 2016 in forum: Mods and Upgrades
  8. digitalsolo
    Post

    Simplify 3d

    I do occasionally have an issue with S3d where it will hang on "heating extruder" if I cancelled a print (due to adhesion issues or anything else)...
    Post by: digitalsolo, Apr 24, 2016 in forum: Software
  9. digitalsolo
    Post

    Z moving negative????

    FWIW I wouldn't superglue anything, but a dot of hot glue won't hurt anything, can be removed later and will definitely lock them in.
    Post by: digitalsolo, Apr 24, 2016 in forum: General Questions
  10. digitalsolo
    Post

    First test of FLEKS 3D build plate kit

    That seems to be a common thread; the product isn't bad (though some have better luck than others) but the company certainly doesn't seem to be...
    Post by: digitalsolo, Apr 24, 2016 in forum: Show and Tell
  11. digitalsolo
    Post

    Printer Number 2

    I'm in the process of building an aluminum extrusion Ultimaker 2 clone to go with my Robo. Been going well, though I had a clog in the Robo...
    Post by: digitalsolo, Apr 20, 2016 in forum: Projects
  12. digitalsolo
    Post

    Simplify 3d

    Just tried out Simplify3D for my printing. I turned the speeds way down and tweaked a ton of stuff and I'm very, very happy with it so far....
    Post by: digitalsolo, Apr 14, 2016 in forum: Software
  13. digitalsolo
    Post

    First test of FLEKS 3D build plate kit

    Rough side.
    Post by: digitalsolo, Apr 14, 2016 in forum: Show and Tell
  14. digitalsolo
    Post

    First test of FLEKS 3D build plate kit

    I've had mixed luck with mine as I've used it. It takes some fiddling with z-height offset to get it just right, and I still etch into the...
    Post by: digitalsolo, Apr 14, 2016 in forum: Show and Tell
  15. digitalsolo
    Post

    Marlin Firmware Upgrade 1.1.0 RC8 & RCBugFix (For R1 & R1+PLUS)

    Wow, thanks WheresWaldo! Just did an update to RC5 and did mesh bed leveling... FINALLY I can use my whole print bed. For some reason the...
    Post by: digitalsolo, Apr 13, 2016 in forum: Mods and Upgrades
  16. digitalsolo
    Post

    First test of FLEKS 3D build plate kit

    It's just plastic, a good sharp blade should cut it fine. SHARP will be key so that you don't make a mess of it.
    Post by: digitalsolo, Apr 5, 2016 in forum: Show and Tell
  17. digitalsolo
    Post

    Build Plates - Are they all the same?

    I have used hairspray/glue stick with pretty good results, probably 90% success rate with PLA and 95% with ABS (60/90* bed temps respectively)....
    Post by: digitalsolo, Apr 5, 2016 in forum: Mods and Upgrades
  18. digitalsolo
    Post

    Solved Something's wrong with my Z-axis

    This video can be really handy to SEE some of what can be done: [MEDIA]
    Post by: digitalsolo, Apr 3, 2016 in forum: Troubleshooting
  19. digitalsolo
    Post

    ROBO 3D Spray Shield

    Thanks, adding these to my "hit list" to build next. :)
    Post by: digitalsolo, Apr 1, 2016 in forum: Show and Tell
  20. digitalsolo
    Post

    Do you watch your prints being made?

    I am pretty new to this still, so I'm pretty amazed watching it all happen. I tell my wife it's all magic. :D
    Post by: digitalsolo, Mar 29, 2016 in forum: Off Topic
Showing results 1 to 20 of 21 Next >
Search Again
Page 1 of 2