1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
  1. aliedholm
    Post

    First test of FLEKS 3D build plate kit

    So, update on my build plates situation. I received a new kit from them as promised. I have them installed and they are working great.
    Post by: aliedholm, Jul 15, 2016 in forum: Show and Tell
  2. aliedholm
    Post

    First test of FLEKS 3D build plate kit

    After feeling abandoned by Fleks3D I received an email from them saying that they had discovered issues in their latest manufacturing run of 10x10...
    Post by: aliedholm, Apr 29, 2016 in forum: Show and Tell
  3. aliedholm
    Post

    Best Filament for Irragation Fittings

    Thanks for your help, I am new to making things so its really helpful to at least have some directions to start researching.
    Post by: aliedholm, Apr 22, 2016 in forum: Printing Filament
  4. aliedholm
    Post

    Best Filament for Irragation Fittings

    Do you know if PC holds up to water well over time and if there is a good solvent bonding solution to PVC for it?
    Post by: aliedholm, Apr 22, 2016 in forum: Printing Filament
  5. aliedholm
    Thread

    Best Filament for Irragation Fittings

    I am looking in to setting up a garden with custom irrigation and using 3d printed parts for the fittings. These pieces will be outside in the...
    Thread by: aliedholm, Apr 22, 2016, 12 replies, in forum: Printing Filament
  6. aliedholm
    Post

    E3D v6 Information, Installation Guides, and Review

    I am about to install the 1.75mm direct drive v6 in my R1+. Do the same things apply to drilling out the wades extruder to run the PTFE tube up...
    Post by: aliedholm, Apr 20, 2016 in forum: Mods and Upgrades
  7. aliedholm
    Post

    Answered Stripped threading in heatsink/heatbreak set screw hole

    Do you know if the volcano pack works with the R1+? Is the extruder motor enough to keep up with a 1.2mm nozzle?
    Post by: aliedholm, Apr 19, 2016 in forum: Troubleshooting
  8. aliedholm
    Post

    Answered Stripped threading in heatsink/heatbreak set screw hole

    Looks like I get to do that E3D V6 upgrade I have been wanting to do. Thanks for the quick answer.
    Post by: aliedholm, Apr 19, 2016 in forum: Troubleshooting
  9. aliedholm
    Thread

    Answered Stripped threading in heatsink/heatbreak set screw hole

    I have a Robo3D R1+. My hotend became clogged and when I took the hotend apart for the first time to clear it upon putting it back together the...
    Thread by: aliedholm, Apr 19, 2016, 5 replies, in forum: Troubleshooting
  10. aliedholm
    Post

    First test of FLEKS 3D build plate kit

    Well, I asked the company if they could do anything for me and I have received no response and it seems like I probably will not. However after...
    Post by: aliedholm, Apr 16, 2016 in forum: Show and Tell
  11. aliedholm
    Post

    First test of FLEKS 3D build plate kit

    When printing with your fleks plate, do you print on the smoother or rougher surface?
    Post by: aliedholm, Apr 14, 2016 in forum: Show and Tell
  12. aliedholm
    Post

    First test of FLEKS 3D build plate kit

    I just received my 10x10 fleks system a couple of days ago and I have been playing with it. The plates on mine also seemed to show up warped. I...
    Post by: aliedholm, Apr 14, 2016 in forum: Show and Tell
Showing results 1 to 12 of 12
Search Again