1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 1 of 2
  1. BR3M3RB
    Post

    Solved Firmware - Extruder Min Temp - MC

    Is there a way to modify the extruder min temp directly from the HEX file I already have?
    Post by: BR3M3RB, Aug 12, 2020 in forum: Troubleshooting
  2. BR3M3RB
    Post

    How to Update Robo firmware with MatterControl

    Thanks! ;)
    Post by: BR3M3RB, Aug 12, 2020 in forum: Software
  3. BR3M3RB
    Post

    Solved Firmware - Extruder Min Temp - MC

    Thanks man! I just don't get why these roboguys don't just put a list of all the firmwares in the same place, I've been to like five different...
    Post by: BR3M3RB, Aug 12, 2020 in forum: Troubleshooting
  4. BR3M3RB
    Post

    Unanswered Best Interface for Robo 3D R1+

    Do you know if there's a way to pre-heat and home all axis in Cura with a single click? I mean without having to program and run some Gcode to do it.
    Post by: BR3M3RB, Aug 12, 2020 in forum: Troubleshooting
  5. BR3M3RB
    Post

    How to Update Robo firmware with MatterControl

    Hi, I'm having an issue while updating the firmware via MatterControl. I downloaded the firmware from...
    Post by: BR3M3RB, Aug 12, 2020 in forum: Software
  6. BR3M3RB
    Thread

    Solved Firmware - Extruder Min Temp - MC

    So I wanted to lower the minimum temperature to extrude before the printer detects an error. I downloaded the firmware from here...
    Thread by: BR3M3RB, Aug 12, 2020, 7 replies, in forum: Troubleshooting
  7. BR3M3RB
    Thread

    Unanswered Best Interface for Robo 3D R1+

    I've been printing with my two Robo 3D R1+ for a while now always from the SD or micro SD card. When I used to print directly from MatterControl I...
    Thread by: BR3M3RB, Aug 5, 2020, 4 replies, in forum: Troubleshooting
  8. BR3M3RB
    Post

    Answered MOSFET TRANSISTOR R1+

    And just to make sure.. this MOSFETs are N channel 60 V 55A TO-220 right?
    Post by: BR3M3RB, Aug 1, 2018 in forum: Troubleshooting
  9. BR3M3RB
    Post

    Answered MOSFET TRANSISTOR R1+

    Thanks ;) Lol! wall art! I'll do that if replacing the MOSFET doesn't work ;) Regards
    Post by: BR3M3RB, Aug 1, 2018 in forum: Troubleshooting
  10. BR3M3RB
    Post

    Answered MOSFET TRANSISTOR R1+

    Yeah I know it's cheaper to replace it, but I'm not a fan of contributing to the electronic waste problem the world is facing. I attached an...
    Post by: BR3M3RB, Aug 1, 2018 in forum: Troubleshooting
  11. BR3M3RB
    Thread

    Answered MOSFET TRANSISTOR R1+

    Im trying to fix some issues with my RAMPS board without replacing it. So I need to replace the MOSFET from the extruder, problem is I don't know...
    Thread by: BR3M3RB, Aug 1, 2018, 7 replies, in forum: Troubleshooting
  12. BR3M3RB
    Post

    Replacing RAMPS 1.4 Controller board?

    If i wanted to replace the MOSFET, how do I know which one is for the bed and which for the extruder? And what are the specs for this MOSFET...
    Post by: BR3M3RB, Jul 25, 2018 in forum: Mods and Upgrades
  13. BR3M3RB
    Post

    Replacing RAMPS 1.4 Controller board?

    Has anyone gotten a new board from Robo3D? Is this covered by the warranty?
    Post by: BR3M3RB, Jul 25, 2018 in forum: Mods and Upgrades
  14. BR3M3RB
    Post

    Replacing RAMPS 1.4 Controller board?

    Is there a site to buy the exact same one the R1+ uses? EDIT: Without paying 150 (Robo3D official site) I've been having lots of issues tweaking...
    Post by: BR3M3RB, Jul 25, 2018 in forum: Mods and Upgrades
  15. BR3M3RB
    Post

    Replacing RAMPS 1.4 Controller board?

    I was having issues with my heatbed. I was told to check the green connectors on the RAMPS board and noticed they were fried. So I desoldered the...
    Post by: BR3M3RB, Jul 25, 2018 in forum: Mods and Upgrades
  16. BR3M3RB
    Post

    Partially Solved Heated bed 2 pin connector

    Hi, can anyone tell me if the pitch is 5.08 mm or 7.62 mm? Thks
    Post by: BR3M3RB, Mar 21, 2018 in forum: Troubleshooting
  17. BR3M3RB
    Post

    Answered Top layer issues (overheating? speed? infill?)

    Thanks Mark Just one last question.. would you keep the last layer at 50ish mm/sec or faster due to the heat transfer?
    Post by: BR3M3RB, Aug 2, 2017 in forum: Troubleshooting
  18. BR3M3RB
    Post

    Answered Top layer issues (overheating? speed? infill?)

    I don't think the number of solid layers on top/bottom is the issue, cause you can see the first model I printed (last 2 pics) was with only 1...
    Post by: BR3M3RB, Aug 2, 2017 in forum: Troubleshooting
  19. BR3M3RB
    Thread

    Answered Top layer issues (overheating? speed? infill?)

    Im using a Robo3D R1+ and having trouble with my last layers printing PLA at 210º and 55º ont he bed. Im printing first layer at 10 mm/sec. and it...
    Thread by: BR3M3RB, Aug 2, 2017, 6 replies, in forum: Troubleshooting
  20. BR3M3RB
    Thread

    How to Update Robo firmware with MatterControl

    Hello every one. Im trying to refresh the firmware in my robo 3d r1+ but it won't let me choose the HEX file. Do I need to put this file in a...
    Thread by: BR3M3RB, May 21, 2017, 5 replies, in forum: Software
Showing results 1 to 20 of 21 Next >
Search Again
Page 1 of 2