1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 1 of 2
  1. Ezra Ehrhard
    Post

    Simplified Titan Mount

    Yogi, When I tried your fan mount I was getting some dragging on the print. I hope you dont mind I took the liberty of remixing your carriage and...
    Post by: Ezra Ehrhard, Jun 4, 2016 in forum: Mods and Upgrades
  2. Ezra Ehrhard
    Post

    E3D Titan Extruder

    Does that motor provide enough torque? I have noticed the 25mm gets super hot (enough to soften and indent the PLA mount i printed). I wasnt sure...
    Post by: Ezra Ehrhard, Jun 3, 2016 in forum: Mods and Upgrades
  3. Ezra Ehrhard
    Post

    Simplified Titan Mount

    Thats looking really good. I was going a different route. Once you have them where you want them let me know I may build in a JST connector into...
    Post by: Ezra Ehrhard, Jun 3, 2016 in forum: Mods and Upgrades
  4. Ezra Ehrhard
    Post

    Simplified Titan Mount

    Hey Yogi are you by any chance planning to model a second fan? The current shroud is set back quite a bit from the hot end and I end up with heat...
    Post by: Ezra Ehrhard, Jun 2, 2016 in forum: Mods and Upgrades
  5. Ezra Ehrhard
    Post

    E3D Titan Extruder

    You can get the 20mm from Amazon but it requires an adapter if you want to use existing wiring. It has wiring going directly into motor, not a...
    Post by: Ezra Ehrhard, Jun 2, 2016 in forum: Mods and Upgrades
  6. Ezra Ehrhard
    Post

    X - Idler with Dual Cable Chains for wire management

    Cool. I like it.
    Post by: Ezra Ehrhard, May 30, 2016 in forum: Mods and Upgrades
  7. Ezra Ehrhard
    Post

    X - Idler with Dual Cable Chains for wire management

    I thought about that. The kit BB takes about 10-12 hours to assemble according to Tom so it will be a nice project regardless. I'm really liking...
    Post by: Ezra Ehrhard, May 30, 2016 in forum: Mods and Upgrades
  8. Ezra Ehrhard
    Post

    X - Idler with Dual Cable Chains for wire management

    You aren't kidding. I started shopping for a second printer a month after getting the robo. I wish I had the time to build from scratch. May go...
    Post by: Ezra Ehrhard, May 28, 2016 in forum: Mods and Upgrades
  9. Ezra Ehrhard
    Post

    X - Idler with Dual Cable Chains for wire management

    The wire to the carriage components are plenty long but there is almost certainly going to be some wires that may need lengthening. My stock wires...
    Post by: Ezra Ehrhard, May 28, 2016 in forum: Mods and Upgrades
  10. Ezra Ehrhard
    Post

    X - Idler with Dual Cable Chains for wire management

    Here is the version to attach to stock Idler. I am drilling pilot holes and 10mm screws to mount it. Its uploading to Thingiverse now. [ATTACH]...
    Post by: Ezra Ehrhard, May 28, 2016 in forum: Mods and Upgrades
  11. Ezra Ehrhard
    Post

    X - Idler with Dual Cable Chains for wire management

    I'll add it to thingiverse today update here once it's done.
    Post by: Ezra Ehrhard, May 28, 2016 in forum: Mods and Upgrades
  12. Ezra Ehrhard
    Post

    X - Idler with Dual Cable Chains for wire management

    It is a super tight fit. I had to tap them in. I would give it some space. I used the X idler from the robo model Mike Kelly posted. Never...
    Post by: Ezra Ehrhard, May 28, 2016 in forum: Mods and Upgrades
  13. Ezra Ehrhard
    Post

    X - Idler with Dual Cable Chains for wire management

    Yes. I just havent exactly decided how I want it to mount. I was thinking about doing something like this...
    Post by: Ezra Ehrhard, May 24, 2016 in forum: Mods and Upgrades
  14. Ezra Ehrhard
    Post

    Simplified Titan Mount

    KTMDirtFace - I am printing a carriage for those bearing right now. I was shocked I ordered them like Friday afternoon and they showed up today. I...
    Post by: Ezra Ehrhard, May 23, 2016 in forum: Mods and Upgrades
  15. Ezra Ehrhard
    Post

    E3D Titan Extruder

    I wont worry too much about it. Until it starts to shred at the end of the 12 hour print! :) Mine seems to mostly work fine. I got mine from...
    Post by: Ezra Ehrhard, May 23, 2016 in forum: Mods and Upgrades
  16. Ezra Ehrhard
    Thread

    X - Idler with Dual Cable Chains for wire management

    Thingiverse location : http://www.thingiverse.com/thing:1583484 Hey guys. I originally showed the start of my work in the main titan thread and...
    Thread by: Ezra Ehrhard, May 23, 2016, 16 replies, in forum: Mods and Upgrades
  17. Ezra Ehrhard
    Post

    E3D Titan Extruder

    Is E3D replacing the bolt? While I have a Holographic sticker I am fairly certain that I have the older hobb. I was shredding the Flashforge PLA...
    Post by: Ezra Ehrhard, May 23, 2016 in forum: Mods and Upgrades
  18. Ezra Ehrhard
    Post

    Simplified Titan Mount

    That looks like a decent enough chain as well. I like the right angle link although I am not sure what I would use it for. Here is the one I...
    Post by: Ezra Ehrhard, May 21, 2016 in forum: Mods and Upgrades
  19. Ezra Ehrhard
    Post

    E3D Titan Extruder

    I have not. I used meshlab to fix the manifold vertices but my lack of skills stepped in i think. I thought it was watertight, used FreeCAD to...
    Post by: Ezra Ehrhard, May 19, 2016 in forum: Mods and Upgrades
  20. Ezra Ehrhard
    Post

    E3D Titan Extruder

    Thanks for the info. I start a new thread once I am ready to share. I am still trying to make it all work! I looked for X Idlers on Thingiverse...
    Post by: Ezra Ehrhard, May 19, 2016 in forum: Mods and Upgrades
Showing results 1 to 20 of 31 Next >
Search Again
Page 1 of 2