1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
  1. jdogid
    Post

    Solved Axis Homing and Move Issues

    It was the Arduino.
    Post by: jdogid, Dec 10, 2019 in forum: Troubleshooting
  2. jdogid
    Post

    Solved Axis Homing and Move Issues

    That's what I'm thinking. Would you say replace all the boards first, and then if that doesn't work, replace the motors second?
    Post by: jdogid, Dec 4, 2019 in forum: Troubleshooting
  3. jdogid
    Post

    Solved Axis Homing and Move Issues

    See, it even refuses to move down when they are CLOSED. It makes that noise similar to the 2nd video.
    Post by: jdogid, Dec 4, 2019 in forum: Troubleshooting
  4. jdogid
    Post

    Solved Axis Homing and Move Issues

    Video on how it dies not like to move down even with all stops open: [MEDIA] Video of the noises it makes when it takes over itself: [MEDIA]
    Post by: jdogid, Dec 4, 2019 in forum: Troubleshooting
  5. jdogid
    Post

    Solved Axis Homing and Move Issues

    Thanks! I'll look at those I did get a print log from MatterControl. I am not sure if this helps diagnose anything. N5 M105*34 ok T:20.0 /0.0...
    Post by: jdogid, Dec 4, 2019 in forum: Troubleshooting
  6. jdogid
    Post

    Solved Axis Homing and Move Issues

    Yep R1+. I followed the steps to flash the firmware, but still no luck.
    Post by: jdogid, Dec 4, 2019 in forum: Troubleshooting
  7. jdogid
    Post

    Solved Axis Homing and Move Issues

    The standard R1+ zip.
    Post by: jdogid, Dec 4, 2019 in forum: Troubleshooting
  8. jdogid
    Post

    Solved Axis Homing and Move Issues

    https://help.robo3d.com/hc/en-us/articles/115000717071-Updating-firmware-with-Arduino I have the R1+. I also had to replace the SDbase files as...
    Post by: jdogid, Dec 4, 2019 in forum: Troubleshooting
  9. jdogid
    Thread

    Solved Axis Homing and Move Issues

    I recently dusted off my R1+, reflashed the firmware, and am not sure what it happening. When I AutoHome the printer, the X and Y axis home fine,...
    Thread by: jdogid, Dec 3, 2019, 22 replies, in forum: Troubleshooting
  10. jdogid
    Post

    Solved Multiple Issues

    The wires that go to the extruder were right next to the X axis motor. I was thinking that it could have been the magnetic field from the front of...
    Post by: jdogid, Apr 28, 2016 in forum: Troubleshooting
  11. jdogid
    Post

    Solved Multiple Issues

    Still shifting. I might add better cooling to the bottom instead of that small fan to see if that helps.
    Post by: jdogid, Apr 26, 2016 in forum: Troubleshooting
  12. jdogid
    Post

    Solved Multiple Issues

    So I adjusted the driver potentiometers and it seemed to not shift with the part. I will print a few more to see if it stays that way. Thanks
    Post by: jdogid, Apr 25, 2016 in forum: Troubleshooting
  13. jdogid
    Post

    Solved Multiple Issues

    I just printed something else after really tightening the belts, and it shifted in both directions. Should I just contact support to see if i can...
    Post by: jdogid, Apr 23, 2016 in forum: Troubleshooting
  14. jdogid
    Post

    Solved Multiple Issues

    How about now? [MEDIA]
    Post by: jdogid, Apr 23, 2016 in forum: Troubleshooting
  15. jdogid
    Post

    Solved Multiple Issues

    So I added a few more tenisoners to the belt, and I'm currently printing something. I am now able to post a video of it actually messing up. [MEDIA]
    Post by: jdogid, Apr 23, 2016 in forum: Troubleshooting
  16. jdogid
    Post

    Solved Multiple Issues

    So I've checked the RAMPS board, and all of the heat sinks are intact. I also printed from the SD card, and it still skipped. I'm going to try and...
    Post by: jdogid, Apr 23, 2016 in forum: Troubleshooting
  17. jdogid
    Post

    Solved Multiple Issues

    Thanks. I'll check those out, and post an update.
    Post by: jdogid, Apr 22, 2016 in forum: Troubleshooting
  18. jdogid
    Post

    Solved Multiple Issues

    OK thanks. I won't be able to try printing from the sd card, as I don't have access to a microSD at the moment and i don't have an LCD screen for...
    Post by: jdogid, Apr 22, 2016 in forum: Troubleshooting
  19. jdogid
    Thread

    Solved Multiple Issues

    I’ve had my R1+ for 4 months now, and everything has been working fine. I haven’t noticed anything wrong with it until a few weeks ago. My prints...
    Thread by: jdogid, Apr 22, 2016, 25 replies, in forum: Troubleshooting
Showing results 1 to 19 of 19
Search Again