1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
  1. Ed Govednik
    Post

    Nothing sliced with Cura is printing on the R2

    Guys, I figured it out. I was using the generic profile for the machine and not the ones provided from Robo. I switched to a medium profile,...
    Post by: Ed Govednik, Oct 25, 2018 in forum: Troubleshooting
  2. Ed Govednik
    Post

    Nothing sliced with Cura is printing on the R2

    Thanks for the replies. I'm not using Octoprint, I just slice everything to a USB drive. One of the first things after removing all the startup...
    Post by: Ed Govednik, Oct 25, 2018 in forum: Troubleshooting
  3. Ed Govednik
    Post

    Nothing sliced with Cura is printing on the R2

    Very curious to what people come up with. I'm helping a friend get his R2 working, and after fixing a smattering of issues, I can print test...
    Post by: Ed Govednik, Oct 24, 2018 in forum: Troubleshooting
  4. Ed Govednik
    Post

    Answered Replacement hotend missing grub for thermistor

    Thanks Mark. Yeah, when I first purchased the hot end replacement kit, I didn't realize it was for the older non plus version of the R1, hence the...
    Post by: Ed Govednik, Aug 28, 2017 in forum: Troubleshooting
  5. Ed Govednik
    Post

    Answered Replacement hotend missing grub for thermistor

    Well, that is a bummer. I didn't mean to end up with the older hex hot end. Anyone know what happens when the boot wears out or tears? Do you...
    Post by: Ed Govednik, Aug 28, 2017 in forum: Troubleshooting
  6. Ed Govednik
    Post

    Answered Replacement hotend missing grub for thermistor

    Oh man, I might have answered my own question. There is a rubber boot that came with the kit. Is that the expectation? You slide this rubber boot...
    Post by: Ed Govednik, Aug 27, 2017 in forum: Troubleshooting
  7. Ed Govednik
    Thread

    Answered Replacement hotend missing grub for thermistor

    Hey all! Hope someone can lend a hand. I have a Robo3d R1+, and I finally encountered a clog that I cannot remove from the throat using normal...
    Thread by: Ed Govednik, Aug 27, 2017, 7 replies, in forum: Troubleshooting
  8. Ed Govednik
    Thread

    JeeQ Data reveals best selling 3D Printers for 2016. Look at that Robo!

    For those who read 3D Print magazine, the Robo looks to be the number one best seller for Best Buy and #13 for Amazon....
    Thread by: Ed Govednik, Jul 14, 2016, 0 replies, in forum: Off Topic
  9. Ed Govednik
    Post

    Solved Left z stepper rod not moving, is buzzing

    The printer is assembled and printing first test part. So far so good. Looks like I could have saved myself a lot of time tearing down the...
    Post by: Ed Govednik, Jun 11, 2016 in forum: Troubleshooting
  10. Ed Govednik
    Post

    Solved Left z stepper rod not moving, is buzzing

    OK, so I am hopeful I just have a loose wire. I removed the z rod, spun the motor freely (it does) then traced the wires back to the RAMPS board....
    Post by: Ed Govednik, Jun 11, 2016 in forum: Troubleshooting
  11. Ed Govednik
    Thread

    Solved Left z stepper rod not moving, is buzzing

    Hey folks, need some help. I finished an overnight print and noticed at the top of my print a weird banding, but the print completed. When I...
    Thread by: Ed Govednik, Jun 11, 2016, 8 replies, in forum: Troubleshooting
  12. Ed Govednik
    Post

    Is the E3D v6 upgrade still needed on the R1+

    *Puts on tin foil hat* [IMG]
    Post by: Ed Govednik, Jun 3, 2016 in forum: General Questions
  13. Ed Govednik
    Post

    Is the E3D v6 upgrade still needed on the R1+

    You could also be paranoid like some of us (well, me) and order a replacement hex kit, a couple NEMA17 motors, replacement linear bearings, print...
    Post by: Ed Govednik, Jun 3, 2016 in forum: General Questions
  14. Ed Govednik
    Post

    Solved Y-axis offset adjustment

    Good to know. It hasn't been a problem so far. I was worried since MatterControl was showing something dead center in the model I was printing...
    Post by: Ed Govednik, May 6, 2016 in forum: Troubleshooting
  15. Ed Govednik
    Post

    Solved Y-axis offset adjustment

    I've been printing for roughly 3 weeks now and love it! I have the same issue as you in that my print bed is off by some degree. When the nine...
    Post by: Ed Govednik, May 6, 2016 in forum: Troubleshooting
Showing results 1 to 15 of 15
Search Again