1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 1 of 2
  1. NaughtyGarfield
    Post

    Unresolved First layer support seems broken and sticking up

    My first layer speed is at 50%. Is lower the percentage the slower the movement? My normal print -0.8 is perfect, however I will lower it and...
    Post by: NaughtyGarfield, Jun 14, 2016 in forum: Troubleshooting
  2. NaughtyGarfield
    Post

    Unresolved First layer support seems broken and sticking up

    Hello GeoF, duh me.. Sorry so new at this.. I remember you told me about it.. Currently I have the Z offset at -0.8 and that was the result. Yeah...
    Post by: NaughtyGarfield, Jun 14, 2016 in forum: Troubleshooting
  3. NaughtyGarfield
    Post

    Unresolved First layer support seems broken and sticking up

    Sorry that I wasn't specific.. I used the same settings and normally pretty much everything I print was fine, but seems when I am printing finer...
    Post by: NaughtyGarfield, Jun 14, 2016 in forum: Troubleshooting
  4. NaughtyGarfield
    Thread

    Unresolved First layer support seems broken and sticking up

    Today I tried to print something that I wanted to print for a while but the first time I tried was with MC and the whole support was a solid...
    Thread by: NaughtyGarfield, Jun 14, 2016, 9 replies, in forum: Troubleshooting
  5. NaughtyGarfield
    Post

    Solved Simplify3D Print Bed Calibration Issues

    Yes, that's what I figured. Because when I was printing at -0.9 it was perfect however the outer layout is not sticking as well as I would like....
    Post by: NaughtyGarfield, Jun 8, 2016 in forum: Troubleshooting
  6. NaughtyGarfield
    Post

    Solved Simplify3D Print Bed Calibration Issues

    Hello KTMDirtFace, Oh man.. I have so so much to learn.. This 3D printing thing is so fun! Compared to the other unit I purchased from Monoprice...
    Post by: NaughtyGarfield, Jun 8, 2016 in forum: Troubleshooting
  7. NaughtyGarfield
    Post

    Solved Simplify3D Print Bed Calibration Issues

    Guys, thank you very much!! you guys are really awesome!! Yes, once I added that line everything printed closer, however it was still a bit high...
    Post by: NaughtyGarfield, Jun 8, 2016 in forum: Troubleshooting
  8. NaughtyGarfield
    Post

    Solved Simplify3D Print Bed Calibration Issues

    I know why I am missing that code now.. It seems S3D added a new profile for the newest Robo3d R1+ and that one is missing the code for: M565 Z-1...
    Post by: NaughtyGarfield, Jun 8, 2016 in forum: Troubleshooting
  9. NaughtyGarfield
    Post

    Solved Simplify3D Print Bed Calibration Issues

    Hahah, Thank you guys!! You both said the same.. I wonder why my default doesn't give me that M565 Z-1 ; set the offset for auto-leveling...
    Post by: NaughtyGarfield, Jun 8, 2016 in forum: Troubleshooting
  10. NaughtyGarfield
    Thread

    Solved Simplify3D Print Bed Calibration Issues

    Hello guys and gals, I just bought the Simplify3D after seeing so many people rave about it. However after downloading the latest version and...
    Thread by: NaughtyGarfield, Jun 8, 2016, 21 replies, in forum: Troubleshooting
  11. NaughtyGarfield
    Thread

    Solved Which direction does the fan blows?

    Stupid me when I added a duct to the fan, I forgot to look at the direction of the fan. Now I don't know which side the fan is supposed to face....
    Thread by: NaughtyGarfield, Jun 8, 2016, 0 replies, in forum: Troubleshooting
  12. NaughtyGarfield
    Post

    A couple of questions on build plates...

    Sorry since I was new, all I know was to use factory software that was included with the Robo3D which was MC. I am now considering using...
    Post by: NaughtyGarfield, May 25, 2016 in forum: General Questions
  13. NaughtyGarfield
    Post

    A couple of questions on build plates...

    Hello TomerO, Thanks for the instruction. I did that, and the extruder stops at the last calibration point and it keeps pushing against the build...
    Post by: NaughtyGarfield, May 25, 2016 in forum: General Questions
  14. NaughtyGarfield
    Post

    A couple of questions on build plates...

    Hello Geof, How do you change the script to do auto level first then heat the nozzle? Do you have to modify it on firmware level?
    Post by: NaughtyGarfield, May 24, 2016 in forum: General Questions
  15. NaughtyGarfield
    Post

    Dust Cover anyone?

    Hahaha man.. stop laughing at me.. :D I didn't realize there are more websites out there than just Thingverse lol.. So thanks for sharing these...
    Post by: NaughtyGarfield, May 24, 2016 in forum: General Questions
  16. NaughtyGarfield
    Post

    Dust Cover anyone?

    I know..I wish I can be hardcore users like you guys.. but I ran out of stuff to print. :D Thanks Mark, you are a great help in the community and...
    Post by: NaughtyGarfield, May 24, 2016 in forum: General Questions
  17. NaughtyGarfield
    Post

    Dust Cover anyone?

    Hahaha.. I think I am one of the are ones that don't use it too often.. :D I was thinking more like a dust cover. Like the ones they sell for...
    Post by: NaughtyGarfield, May 24, 2016 in forum: General Questions
  18. NaughtyGarfield
    Thread

    Dust Cover anyone?

    I searched in the forum, and didn't see anyone asked about Dust Cover.. So I guess there isn't one made for the Robo3D printer. How do you guys...
    Thread by: NaughtyGarfield, May 24, 2016, 15 replies, in forum: General Questions
  19. NaughtyGarfield
    Post

    Solved Build plate calibration noise when hitting the end

    Mark, you are good!! It was the wire that's stuck when moving and once I freed the wires, everything is normal now.. Thanks again for all your help!!
    Post by: NaughtyGarfield, May 22, 2016 in forum: Troubleshooting
  20. NaughtyGarfield
    Post

    Solved Build plate calibration noise when hitting the end

    How did you fixed it? Where you using Matter Control?
    Post by: NaughtyGarfield, May 21, 2016 in forum: Troubleshooting
Showing results 1 to 20 of 37 Next >
Search Again
Page 1 of 2