1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
  1. robofish
    Post

    Unanswered Intermittent Squiggly Lines

    I am pretty sure the issue is the printer. I have 2 printers, A and B. A goes to a Mac. B goes to a Windows machine. So, system A and system B....
    Post by: robofish, Jul 7, 2016 in forum: Troubleshooting
  2. robofish
    Post

    Unanswered Intermittent Squiggly Lines

    I don't think it is the bed level alone per se, because it is only making weird lines at a regular intervals. If it was the bed leveling alone, I...
    Post by: robofish, Jul 2, 2016 in forum: Troubleshooting
  3. robofish
    Thread

    Unanswered Intermittent Squiggly Lines

    [ATTACH] [ATTACH] [ATTACH] I am getting squiggly lines at regular intervals. I did find a post about bed leveling being an issue, but how...
    Thread by: robofish, Jul 1, 2016, 8 replies, in forum: Troubleshooting
  4. robofish
    Post

    Solved R1 Plus is printing on right side of bed but not left.

    Problem solved. The solution was to use reading glasses which will allowed my old eyes to see that a wire fell loose from the left leveling switch.
    Post by: robofish, Jun 18, 2016 in forum: Troubleshooting
  5. robofish
    Post

    Solved R1 Plus is printing on right side of bed but not left.

    G28 X0 Y0 Z0 ; home all axes G1 Z5 F5000 ; lift nozzle M109 S[temperature] ; set the extruder temp and wait G28 X0 Y0 Z0 ; Home Z again in case...
    Post by: robofish, Jun 18, 2016 in forum: Troubleshooting
  6. robofish
    Post

    Solved R1 Plus is printing on right side of bed but not left.

    It didn't work. I was skeptical, because isn't that the reason for the auto level? The weird part is it did print all of the little test dollups...
    Post by: robofish, Jun 18, 2016 in forum: Troubleshooting
  7. robofish
    Post

    Solved R1 Plus is printing on right side of bed but not left.

    Do I lower the print head by hand as well or using the control software?
    Post by: robofish, Jun 18, 2016 in forum: Troubleshooting
  8. robofish
    Post

    Solved R1 Plus is printing on right side of bed but not left.

    New to 3d printing. Is there a link to info on how to do that?
    Post by: robofish, Jun 18, 2016 in forum: Troubleshooting
  9. robofish
    Thread

    Solved R1 Plus is printing on right side of bed but not left.

    New, out of the box it was scraping the glass. Not leveling correctly. I added the M565 Z-1.0 in the g code and that helped a bit, but only on the...
    Thread by: robofish, Jun 18, 2016, 11 replies, in forum: Troubleshooting
  10. robofish
    Post

    Solved Jam / Clog new R1 plus

    That was the problem. I took off the extruder gears to get to it. Had tried the flathead thing but the nut is on too tight. Called ROBO and got...
    Post by: robofish, May 24, 2016 in forum: Troubleshooting
  11. robofish
    Post

    Solved Jam / Clog new R1 plus

    On further inspection, yes it is. I am a newb. Do I have to take the whole assembly apart, or what do I take off to get to that nut?
    Post by: robofish, May 23, 2016 in forum: Troubleshooting
  12. robofish
    Post

    Solved Jam / Clog new R1 plus

    Hi Mike, I can't believe I found this thread. I thought I was going crazy with my R1 Plus not matching up with the videos. I have the same...
    Post by: robofish, May 23, 2016 in forum: Troubleshooting
Showing results 1 to 12 of 12
Search Again