1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
  1. Richard Lee
    Post

    Solved Can someone PLEASE kick me in the Z?

    @WheresWaldo , everything seems OK now and the R1+ is printing exceptionally well... Thanks again for your help. Now if I could figure out how...
    Post by: Richard Lee, Jan 2, 2018 in forum: Troubleshooting
  2. Richard Lee
    Post

    Solved Can someone PLEASE kick me in the Z?

    I wanted to start from scratch in order to learn more about configuring Marlin, so I used the base Marlin v1.1.8, and with a bit of trial and...
    Post by: Richard Lee, Jan 2, 2018 in forum: Troubleshooting
  3. Richard Lee
    Post

    Solved Can someone PLEASE kick me in the Z?

    So I should lower X and Y in Line 547 to about 2000 instead of 8000 each? Line 557 is OK to keep at 600?
    Post by: Richard Lee, Jan 2, 2018 in forum: Troubleshooting
  4. Richard Lee
    Profile Post

    Eclectic. Eccentric.

    Eclectic. Eccentric.
    Status update by Richard Lee, Jan 2, 2018
  5. Richard Lee
    Post

    Solved Can someone PLEASE kick me in the Z?

    Are you referring to Line 557 or another?
    Post by: Richard Lee, Jan 2, 2018 in forum: Troubleshooting
  6. Richard Lee
    Post

    Solved Can someone PLEASE kick me in the Z?

    THANK YOU very much, WheresWaldo, the Z offset is working great using only the Line 688 edit. I and getting a lot of vibration (jerk?) when...
    Post by: Richard Lee, Jan 2, 2018 in forum: Troubleshooting
  7. Richard Lee
    Post

    Solved Can someone PLEASE kick me in the Z?

    Post by: Richard Lee, Jan 2, 2018 in forum: Troubleshooting
  8. Richard Lee
    Post

    Solved Can someone PLEASE kick me in the Z?

    Thanks for the reassurance, I couldn't imagine being alone is this confusion....
    Post by: Richard Lee, Jan 1, 2018 in forum: Troubleshooting
  9. Richard Lee
    Post

    Solved Can someone PLEASE kick me in the Z?

    Thanks for the great information. I will definitely include those changes. Under the stock firmware, my Z offset is 1.00 (see attachment) How...
    Post by: Richard Lee, Jan 1, 2018 in forum: Troubleshooting
  10. Richard Lee
    Post

    Solved Can someone PLEASE kick me in the Z?

    Here's my Marlin v1.1.8 config file. Thanks for helping me.
    Post by: Richard Lee, Jan 1, 2018 in forum: Troubleshooting
  11. Richard Lee
    Post

    Solved Can someone PLEASE kick me in the Z?

    Yes, commented with //RL
    Post by: Richard Lee, Jan 1, 2018 in forum: Troubleshooting
  12. Richard Lee
    Thread

    Solved Can someone PLEASE kick me in the Z?

    After getting rid of my POS Airwolf Axiom, I recently put my R1+ (2016 version) back into service and cannot get my Z height configured correctly....
    Thread by: Richard Lee, Jan 1, 2018, 20 replies, in forum: Troubleshooting
  13. Richard Lee
    Post

    Great new slicer software, Craftware.

    Thanks Paul, it would be convenient though. ;-)
    Post by: Richard Lee, Sep 14, 2016 in forum: Software
  14. Richard Lee
    Post

    Great new slicer software, Craftware.

    Question: Can you print to the R1+ directly from CraftWare? I entered the printer settings, including the start/end .gcode (copied from...
    Post by: Richard Lee, Sep 14, 2016 in forum: Software
Showing results 1 to 14 of 14
Search Again