1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 1 of 2
  1. jsam
    Post

    Solved PEI Upgrade and z-offset

    Hey guys, it looks like I've got that elephant foot fixed thanks to your script help. I ran a few single layer prints as suggested and settled on...
    Post by: jsam, Nov 6, 2016 in forum: General Questions
  2. jsam
    Post

    Solved PEI Upgrade and z-offset

    Mark, I found this thread from July where you posted your starting script:...
    Post by: jsam, Nov 5, 2016 in forum: General Questions
  3. jsam
    Post

    Solved PEI Upgrade and z-offset

    Did a manual level with paper, that was a little off so better now. I tried a print with a lower bed temperature but not much improvement. It...
    Post by: jsam, Nov 5, 2016 in forum: General Questions
  4. jsam
    Post

    Solved PEI Upgrade and z-offset

    I use a Mac at home and don't have Notepad. I tried to open it up in the equivalent but it didn't seem to work. I'll try to open the file on my...
    Post by: jsam, Nov 4, 2016 in forum: General Questions
  5. jsam
    Post

    Solved PEI Upgrade and z-offset

    That sounds like a plan danzca6, how do you look a that g-code? Do you import it into a simple text editor or is there something in S3D that will...
    Post by: jsam, Nov 4, 2016 in forum: General Questions
  6. jsam
    Post

    Solved PEI Upgrade and z-offset

    Thanks for pointing that out Robert55, so if I change the Z-axis number (keeping it postive) the nozzle will be further away from the bed correct?...
    Post by: jsam, Nov 4, 2016 in forum: General Questions
  7. jsam
    Post

    PEI Print Bed

    Hi guys, I just did this upgrade to my Robo and won't get a chance to print until this weekend. I was wondering about the autoleveling sequence...
    Post by: jsam, Nov 3, 2016 in forum: Mods and Upgrades
  8. jsam
    Post

    Solved PEI Upgrade and z-offset

    Yes, this is the first time I've looked at the starting script in S3D and I haven't touched any script since I started using it.
    Post by: jsam, Nov 2, 2016 in forum: General Questions
  9. jsam
    Post

    Solved PEI Upgrade and z-offset

    I found the starting script in the FFF profile and I'm not seeing M565, I'm seeing this: G28 ; home all axes G29 ; probe the bed G1 Z5 F5000 ;...
    Post by: jsam, Nov 2, 2016 in forum: General Questions
  10. jsam
    Thread

    Solved PEI Upgrade and z-offset

    So my glass bed chipped earlier this week and I decided to upgrade the bed by adding a sheet of PEI. I used this youtube vid as a guide: [MEDIA]...
    Thread by: jsam, Nov 2, 2016, 20 replies, in forum: General Questions
  11. jsam
    Thread

    Leaving filament loaded in the printer

    Hi guys, Here's another newbie question. Should I leave the filament loaded in the printer after I am done printing for the day or should I...
    Thread by: jsam, Sep 7, 2016, 10 replies, in forum: General Questions
  12. jsam
    Post

    Solved Help with bed leveling switch

    Danzca6, I did the paper level and a few test prints, looks like I'm back in business. Thanks again for the help.
    Post by: jsam, Sep 2, 2016 in forum: Troubleshooting
  13. jsam
    Post

    Solved Help with bed leveling switch

    Thanks danzca6. What's the best way to make sure the x-axis is as level as possible?
    Post by: jsam, Aug 31, 2016 in forum: Troubleshooting
  14. jsam
    Post

    Solved Help with bed leveling switch

    How about that, with a little finagling it popped back in place. Any advice on how to make sure it levels correctly?
    Post by: jsam, Aug 31, 2016 in forum: Troubleshooting
  15. jsam
    Thread

    Solved Help with bed leveling switch

    Hi guys, had a positive and negative night here. I just finished successfully installing the external lcd controller upgrade. I was testing out...
    Thread by: jsam, Aug 31, 2016, 6 replies, in forum: Troubleshooting
  16. jsam
    Post

    Solved MakeShaper PLA Settings

    Thanks Geof, will keep that in mind. Good point, I'll look for some makerspaces in the area.
    Post by: jsam, Aug 27, 2016 in forum: General Questions
  17. jsam
    Post

    Solved MakeShaper PLA Settings

    It's still in transit and should arrive Saturday or early next week. Worse comes to worse I could always donate them to the local high school. I...
    Post by: jsam, Aug 26, 2016 in forum: General Questions
  18. jsam
    Post

    Solved MakeShaper PLA Settings

    Yikes, I just bought two spools of this stuff from them! Wish I saw this thread first.
    Post by: jsam, Aug 26, 2016 in forum: General Questions
  19. jsam
    Post

    Just got my ROBO

    Thanks for the added info everyone. I'm planning on getting the Smart LCD controller from printed solid so I'll add some of that cleaning filament...
    Post by: jsam, Aug 22, 2016 in forum: United States of America
  20. jsam
    Post

    Answered Auto leveling Question

    Hi danzca6, I'm not having any problems (so far) with the printer and have be busily printing a few upgrades (new spool holder and frame for LCD...
    Post by: jsam, Aug 22, 2016 in forum: Troubleshooting
Showing results 1 to 20 of 24 Next >
Search Again
Page 1 of 2