1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 1 of 4
  1. capecodcharlie
    Post

    Unresolved Hardware error

    Oh Me Bad , it's not the Slicer ?? It's the rookie running it , I took a minute and went to look at the settings and sure enough I changed both...
    Post by: capecodcharlie, Aug 24, 2016 in forum: Troubleshooting
  2. capecodcharlie
    Post

    Unresolved Hardware error

    Now I know what a slicer is , I figured as much , I'm not at the computer right now but will look into that setting and see what's there ,, Thanks
    Post by: capecodcharlie, Aug 24, 2016 in forum: Troubleshooting
  3. capecodcharlie
    Post

    Unresolved Hardware error

    No I only changed the one setting to 3 , and I'm not running windows 7 or 10 , That lap top is no long running , I'm on an older one a step down ,...
    Post by: capecodcharlie, Aug 24, 2016 in forum: Troubleshooting
  4. capecodcharlie
    Post

    Unresolved Hardware error

    .i am writing these things down so the next time it won't be that I'll that stupid , ?? Thanks
    Post by: capecodcharlie, Aug 24, 2016 in forum: Troubleshooting
  5. capecodcharlie
    Post

    Unresolved Hardware error

    Newbie , here , Not sure what u mean by that ?? Thanks
    Post by: capecodcharlie, Aug 24, 2016 in forum: Troubleshooting
  6. capecodcharlie
    Post

    Unresolved Hardware error

    Pictures ,, Thanks I always forget them , [ATTACH][ATTACH] [ATTACH][ATTACH]
    Post by: capecodcharlie, Aug 24, 2016 in forum: Troubleshooting
  7. capecodcharlie
    Post

    Unresolved Hardware error

    I have seen people talk about Cura and Simplify 3d , I'll look into it a bit later , On the parts printed I seem to have lost the back , Picture...
    Post by: capecodcharlie, Aug 24, 2016 in forum: Troubleshooting
  8. capecodcharlie
    Post

    Unresolved Hardware error

    You along with al, the others have been one Hugh help , That was great you went out of your way to show me the way to change the settings , I'm...
    Post by: capecodcharlie, Aug 23, 2016 in forum: Troubleshooting
  9. capecodcharlie
    Post

    Unresolved Hardware error

    That's one question I have ?? What is everyone using. It seems no one likes matter ?? I new and open to change , And Thanks for all your help ,...
    Post by: capecodcharlie, Aug 23, 2016 in forum: Troubleshooting
  10. capecodcharlie
    Post

    Unresolved Hardware error

    No I think this is great , what a way to learn , without you all I would be lost , I guess if you understand what the settings mean when checking...
    Post by: capecodcharlie, Aug 23, 2016 in forum: Troubleshooting
  11. capecodcharlie
    Post

    Unresolved Hardware error

    O K Made the change and I'm printing , Thanks
    Post by: capecodcharlie, Aug 23, 2016 in forum: Troubleshooting
  12. capecodcharlie
    Post

    Unresolved Hardware error

    So just put a 3 there and try that ?? No mm ??
    Post by: capecodcharlie, Aug 23, 2016 in forum: Troubleshooting
  13. capecodcharlie
    Post

    Unresolved Hardware error

    Not sure if you can see that but it says Add mm to the end number to specify distance in millimeters ?...[ATTACH]
    Post by: capecodcharlie, Aug 23, 2016 in forum: Troubleshooting
  14. capecodcharlie
    Post

    Unresolved Hardware error

    There at 1mm , how do I get just 3 , .?? Just erase and put a 3 there ??
    Post by: capecodcharlie, Aug 23, 2016 in forum: Troubleshooting
  15. capecodcharlie
    Post

    Unresolved Hardware error

    Are we talking top / Bottom solid layers ?? Set now at 1mm ?? [ATTACH]F
    Post by: capecodcharlie, Aug 23, 2016 in forum: Troubleshooting
  16. capecodcharlie
    Post

    Unresolved Hardware error

    Any of these do it ??. I GENERL / Layers /Surface / then what ??[ATTACH]
    Post by: capecodcharlie, Aug 23, 2016 in forum: Troubleshooting
  17. capecodcharlie
    Post

    Unresolved Hardware error

    Would it be the Perimeters that I ajust ??. Thanks
    Post by: capecodcharlie, Aug 23, 2016 in forum: Troubleshooting
  18. capecodcharlie
    Post

    Unresolved Hardware error

    For got to put picture in , [ATTACH]
    Post by: capecodcharlie, Aug 23, 2016 in forum: Troubleshooting
  19. capecodcharlie
    Post

    Unresolved Hardware error

    O K I found this Layer height.0.2 And then there's first layer height 0.3 mm , perimeters 2 , fill density 0.25 z offset 0 , ( picture included )...
    Post by: capecodcharlie, Aug 23, 2016 in forum: Troubleshooting
  20. capecodcharlie
    Post

    Unresolved Hardware error

    O. K , I'll open the matter control and look around , see if I find anything , ?? Nobody seems to use this ?? What do you all use , ?? Thanks
    Post by: capecodcharlie, Aug 23, 2016 in forum: Troubleshooting
Showing results 1 to 20 of 71 Next >
Search Again
Page 1 of 4