1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
  1. Valor Props
    Post

    Unanswered XXL Controller not working after replacing ramps & arduino

    Haha got my hopes up...they were, just was scrolled to the side a bit xD
    Post by: Valor Props, Sep 4, 2017 in forum: Troubleshooting
  2. Valor Props
    Post

    Unanswered XXL Controller not working after replacing ramps & arduino

    Yup, tried that, the u8glib part I'm still a bit confused by though. But this is what I have and just tried with no change.
    Post by: Valor Props, Sep 4, 2017 in forum: Troubleshooting
  3. Valor Props
    Post

    Unanswered XXL Controller not working after replacing ramps & arduino

    I'm assuming it's something with the firmware as the ramps seems to be doing the same thing and it's the only issue I have right now. I've used...
    Post by: Valor Props, Sep 4, 2017 in forum: Troubleshooting
  4. Valor Props
    Post

    Unanswered XXL Controller not working after replacing ramps & arduino

    Replaced the ramps, same issue but now the controller actually clicks like I'm going through the menu. Still have line 1 & 3 as all rectangles and...
    Post by: Valor Props, Sep 4, 2017 in forum: Troubleshooting
  5. Valor Props
    Post

    Unanswered XXL Controller not working after replacing ramps & arduino

    That's what I was afraid of. I have a generic one. I may have to swap it out then. Do you think I could just swap the ramps board or should I...
    Post by: Valor Props, Sep 4, 2017 in forum: Troubleshooting
  6. Valor Props
    Post

    Unanswered XXL Controller not working after replacing ramps & arduino

    Tried the potentiometer, didn't help, only made the screen brighter/dimmer. As far as I know I wired it correctly, I followed the labeling for the...
    Post by: Valor Props, Sep 4, 2017 in forum: Troubleshooting
  7. Valor Props
    Post

    Unanswered XXL Controller not working after replacing ramps & arduino

    Downloaded the firmware from Robo directly. The part about the potentiometer doesn't make sense to me only because it's the same XXL that was on...
    Post by: Valor Props, Sep 4, 2017 in forum: Troubleshooting
  8. Valor Props
    Thread

    Unanswered XXL Controller not working after replacing ramps & arduino

    So recently I had to replace my Ramps 1.4 on one of my R1+ units. Everything went fine, flashed the firmware to the board and everything compiled....
    Thread by: Valor Props, Sep 4, 2017, 16 replies, in forum: Troubleshooting
  9. Valor Props
    Post

    Unresolved Issue with units shutting down...

    I'll Check the power supply later with my meter. The outlets the machines run off of were all new installed for these, 110V out. Would you have a...
    Post by: Valor Props, Jun 2, 2017 in forum: Troubleshooting
  10. Valor Props
    Thread

    Unresolved Issue with units shutting down...

    Okay, so I posted this about a month ago maybe now, R1+ unit would randomly stop during prints. I tried adding another fan to cool the boards and...
    Thread by: Valor Props, Jun 2, 2017, 5 replies, in forum: Troubleshooting
  11. Valor Props
    Post

    Answered Robo R1+ Stopping mid print

    The fan was working, upgraded it to an 80mm fan and had it located underneath the ramps board. I even separated the fuses a bit as I know they can...
    Post by: Valor Props, May 11, 2017 in forum: Troubleshooting
  12. Valor Props
    Thread

    Answered Robo R1+ Stopping mid print

    Hey guys, thought I'd post here since what I've tried hasn't worked and usually if I've had an issue, this place has already found the answer. So...
    Thread by: Valor Props, May 1, 2017, 4 replies, in forum: Troubleshooting
Showing results 1 to 12 of 12
Search Again